USB driver killed after CID patch VW MSTD2
Добро пожаловать на Turbo Quattro.
Показано с 1 по 14 из 14
  1. #1

    По умолчанию USB driver killed after CID patch VW MSTD2

    Hello,

    we have here an problem with an VW MSTD 2 Delphi

    After using the CID Patch from the knowing manual the USB driver Are killed.
    we try to update/downgrade the firmware but without result.
    there is no access anymore to the unit over Telenet.

    and we need to write this MHConfig to got this working

    is here anybody who can repair this issue?
    if so,please contact me I don’t want this for free this is sure

    regards

  2. #2
    Новичок
    Регистрация
    07.05.2020
    Адрес
    Brasil
    Сообщений
    3

    По умолчанию

    Hello friend, you don't need to do anything but install the firmware again, I had the same problem and solved it by passing the files as an update in SWDL and checking the option ALL

  3. #3
    Новичок
    Регистрация
    11.12.2020
    Адрес
    turkey
    Сообщений
    3

    По умолчанию

    Цитата Сообщение от josuegd13 Посмотреть сообщение
    Hello friend, you don't need to do anything but install the firmware again, I had the same problem and solved it by passing the files as an update in SWDL and checking the option ALL
    this is not working

  4. #4

    По умолчанию

    Usually when USB driver is killed by CID patch, SD Card driver is also killed. So the only solution is jtag or soldering. Correct me if I'm wrong.

  5. #5

    По умолчанию

    Ater my first fult with cid patch only telnet no works (Fw635) next time with fw 891 no cd no sd no usb swdl update not works. Uart connection only log and not posible write commands.
    I think now only jtag

  6. #6
    Новичок
    Регистрация
    27.12.2020
    Адрес
    Ireland
    Сообщений
    5

    По умолчанию

    What I found it is eMMC has to be writen and flash aswell.. So backup need it. I have same unit and there is no usb, no sd,and no telnet...

  7. #7

    По умолчанию

    Hallo zusammen,

    Nach dem MST2_cid.sh ausgeführt wurde, ist USB Port tot und SD Karte mit Firmware erkennt auch nicht.
    Im Moment kann ich weder der Firmware aktualisieren noch über USB to Telnet das Gerät erreichen.
    Über USB-UART kann nur Log-Daten beobachten, keine Eingabe ist möglich.
    Habt ihr Idee ,wie könnte die Unit wiederstellen?
    Daten von meinem MST2:
    Teilnummer: 3Q0035846B
    SW Version: MST2_EU_VW_P9122D
    SW MU Version 0842
    Danke vorab!
    Hi everyone,
    After MST2_cid.sh was executed, USB port is dead and SD card with firmware does not recognize either. At the moment I can neither update the firmware nor access the device via USB to Telnet. Only log data can be observed via USB-UART, no input is possible. Do you have any ideas how could the unit restore? Data from my MST2: Part number: 3Q0035846B SW version: MST2_EU_VW_P9122D SW MU version 0842
    Thanks in advance!

  8. #8

    По умолчанию

    Цитата Сообщение от ulrikhp Посмотреть сообщение
    Hallo zusammen,

    Nach dem MST2_cid.sh ausgeführt wurde, ist USB Port tot und SD Karte mit Firmware erkennt auch nicht.
    Im Moment kann ich weder der Firmware aktualisieren noch über USB to Telnet das Gerät erreichen.
    Über USB-UART kann nur Log-Daten beobachten, keine Eingabe ist möglich.
    Habt ihr Idee ,wie könnte die Unit wiederstellen?
    Daten von meinem MST2:
    Teilnummer: 3Q0035846B
    SW Version: MST2_EU_VW_P9122D
    SW MU Version 0842
    Danke vorab!
    Hi everyone,
    After MST2_cid.sh was executed, USB port is dead and SD card with firmware does not recognize either. At the moment I can neither update the firmware nor access the device via USB to Telnet. Only log data can be observed via USB-UART, no input is possible. Do you have any ideas how could the unit restore? Data from my MST2: Part number: 3Q0035846B SW version: MST2_EU_VW_P9122D SW MU version 0842
    Thanks in advance!
    Write me pm.

  9. #9
    Новичок
    Регистрация
    27.12.2020
    Адрес
    Ireland
    Сообщений
    5

    По умолчанию

    Mst2 sort it. Emmc flash it back with full working img. After that emergency update and unit works. Нажмите на изображение для увеличения
Название: IMG_20210413_194715.jpg
Просмотров: 367
Размер:	46.9 Кб
ID:	70343Нажмите на изображение для увеличения
Название: IMG_20210420_192142.jpg
Просмотров: 424
Размер:	62.7 Кб
ID:	70344Нажмите на изображение для увеличения
Название: IMG_20210420_192142.jpg
Просмотров: 424
Размер:	62.7 Кб
ID:	70344Нажмите на изображение для увеличения
Название: IMG_20210420_192142.jpg
Просмотров: 424
Размер:	62.7 Кб
ID:	70344Нажмите на изображение для увеличения
Название: IMG_20210420_191731.jpg
Просмотров: 377
Размер:	105.0 Кб
ID:	70345

  10. #10

    По умолчанию

    @volksjet Good work! How have you pushed it into emergency update? Or did it start automatically after flash?

  11. #11
    Новичок
    Регистрация
    11.12.2020
    Адрес
    turkey
    Сообщений
    3

    По умолчанию

    Цитата Сообщение от volksjet Посмотреть сообщение
    Mst2 sort it. Emmc flash it back with full working img. After that emergency update and unit works. Нажмите на изображение для увеличения
Название: IMG_20210413_194715.jpg
Просмотров: 367
Размер:	46.9 Кб
ID:	70343Нажмите на изображение для увеличения
Название: IMG_20210420_192142.jpg
Просмотров: 424
Размер:	62.7 Кб
ID:	70344Нажмите на изображение для увеличения
Название: IMG_20210420_192142.jpg
Просмотров: 424
Размер:	62.7 Кб
ID:	70344Нажмите на изображение для увеличения
Название: IMG_20210420_192142.jpg
Просмотров: 424
Размер:	62.7 Кб
ID:	70344Нажмите на изображение для увеличения
Название: IMG_20210420_191731.jpg
Просмотров: 377
Размер:	105.0 Кб
ID:	70345
    How to emergency mode ? Device delphi ?

  12. #12

    По умолчанию

    Подскажите как решить проблему данную? Что чем прошить нужно?

    Tell me how to solve this problem? What do you need to flash with what?

  13. #13
    Пользователь
    Регистрация
    13.07.2018
    Адрес
    EU
    Сообщений
    68

    По умолчанию

    volksjet where are you?? share yours knowledge if do you have any...

  14. #14
    Новичок
    Регистрация
    27.12.2020
    Адрес
    Ireland
    Сообщений
    5

    По умолчанию

    I show enough on pictures but you are not smart enough to find out. So solution what i did is desolder emmc read it by external programmer then reprogramm it. make reballing on nand which is emmc 153. Solder back. Put flash files on sd card and thats it. Hope this help you fix your units.

 

 

Ваши права

  • Вы не можете создавать новые темы
  • Вы не можете отвечать в темах
  • Вы не можете прикреплять вложения
  • Вы не можете редактировать свои сообщения
  •  
Back to top