MIB JITAG - Страница 3
Добро пожаловать на Turbo Quattro.
Страница 3 из 3 ПерваяПервая 123
Показано с 41 по 51 из 51

Тема: MIB JITAG

  1. #41
    Пользователь
    Регистрация
    11.03.2016
    Сообщений
    96

    По умолчанию

    BCT is specific for board model.

  2. #42
    Пользователь
    Регистрация
    08.04.2019
    Сообщений
    35

    По умолчанию

    thanks congo, i am stuck in EFU red menu flash is damaged , JTAG can't connect, and i have no backup :-( , so only way is to desolder and read SGL ?

  3. #43
    Новичок
    Регистрация
    29.07.2020
    Адрес
    Hessen
    Сообщений
    23

    По умолчанию

    @aleka

    I'm still stuck with the issue:
    Вложение 69214

    Any ideas?

  4. #44
    Пользователь
    Регистрация
    08.04.2019
    Сообщений
    35

    По умолчанию

    i tested tegrarcm uploaded BCT and qboot works, connection for JTAG is then unlocked and working it start to read SGL512 but the unit reboots after 1min so i cant read or write the flash.

  5. #45
    Новичок
    Регистрация
    29.07.2020
    Адрес
    Hessen
    Сообщений
    23

    По умолчанию

    How far gone is your MMX?

    Mine is completly dead and I do not have success with the qboot and BCT I extracted from my MMX backup.

    Could you share your setting or compare with mine I postet earlier?

  6. #46
    Пользователь
    Регистрация
    08.04.2019
    Сообщений
    35

    По умолчанию

    mine is also completly dead i flashed the QB_primary and QB_Recovery to the adresses which was posted here in this thread, after it shows stage2 bootloader failed to load.

    Using nvflash you are supposed to able to flash MMX as well ������.

    with nvflash it should be possible to flash the NOR then no Jtag is need , ;-)

  7. #47

    По умолчанию

    Цитата Сообщение от congo Посмотреть сообщение
    Somebody can explain how to restart or pause watchdog in MIB1? or copy here, I dont have acess to this link... :-(

  8. #48
    Пользователь
    Регистрация
    08.04.2019
    Сообщений
    35

    По умолчанию

    reading is working fine , but i never could write it , i think there maybe must set TRST low maybe

  9. #49

    По умолчанию

    Цитата Сообщение от Kastrati Посмотреть сообщение
    Somebody can explain how to restart or pause watchdog in MIB1? or copy here, I dont have acess to this link... :-(
    Info: for Mib1, after login in emergency mode you must execute "slay -9 MIBEmergency" and it stop reboot and counter.
    Последний раз редактировалось Kastrati; 18.11.2020 в 16:16.

  10. #50

    По умолчанию

    Цитата Сообщение от aleka Посмотреть сообщение
    You can not write full flash due reboot, but first part of mmx dump have Emergency tool. Due the Emergency tool you can write whole flash.
    Hi @aleka , Do you now if is possible to flash eifs.img from emergency mode?. (MIB1 MHIG)
    I have full time access to emergency by Uart but i dont know telnet passwd. The unit have some problems and I try to repair it reflashing.

  11. #51

    По умолчанию

    Цитата Сообщение от congo Посмотреть сообщение
    A0000 -> qb_recovery.img 262144


    120000 -> qb_primary.img 262144


    760000 -> mifs-stage1.img 3145728


    A60000 -> mifs-stage2.img 48234496


    160000 -> eifs.img 6291456


    0x03600000 -> efs-system.img 2097152


    0x03800000 -> efs-persist.img

    Some of my notes.
    Only to correct this, if "A60000 -> mifs-stage2.img 48234496" it is long to 0x0385FFFF therefore overwrites 0x03600000 -> efs-system.img 2097152 and 0x03800000 -> efs-persist.img, My correction is:

    120000 -> qb_primary.img 262144


    760000 -> mifs-stage1.img 3145728


    A60000 -> mifs-stage2.img 48234496


    160000 -> eifs.img 6291456


    0x03A40000 -> efs-system.img 2097152


    0x03EC0000 -> efs-persist.img
    Последний раз редактировалось Kastrati; 05.01.2021 в 18:46.

 

 

Ваши права

  • Вы не можете создавать новые темы
  • Вы не можете отвечать в темах
  • Вы не можете прикреплять вложения
  • Вы не можете редактировать свои сообщения
  •  
Back to top