Turbo Quattro

Certainly not so easy to do!
I would understand where to find them also!!

calling devctl with erase struct:
status: 0
offset: 0xb80000
limit: 0x40000
devctl(11,-2146694912,xx,12,0) returned 0OnOff: Progress 012
dev_fd == 11
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0xbc0000
limit: 0x40000
devctl(11,-2146694912 ...

SWDL: read finished (524288, 0)
devctl(12,-2146694912,xx,12,0) returned 0SWDL: read finished (524288, 524288)
dev_fd == 12
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0x7c0000
limit: 0x40000
SWDL: read finished (524288, 1048576)
SWDL: read ...

IPL: Audi 3G 9308 (SH7785) / QNX 6.3.0 [PL_qnx_ipl-3g_9308-sh7785_07412A, built 2007/10/09_12-19-44_UTC]
CPU: SH7785 (>= 5th cut, clk mode 20), 792MHz
RAM: 512 MB (probed, DBCONF=e30002)
FLASH: Spansion S29GL512N: 512 sectors x 256K
FPGA: PL_MMI3G_FPGA_9308_D1_08492A
(0ms)
*** emergency FPGA loaded ...

No unfortunately it is dead....it begins the emergency update but it cannot finish!!!

Second Miracle!!!

Where to find those DDR???

Crash-100 писал(а):testing [48000000..4fffffff]: DDR_SS512_X_SCAN ......./ ** FAILED!
I was right !!!!! This trible is very hard to FIX. you must change 4 DRAM - DDR chip.

MIRACLE IT STARTED!!
iT is re-doing the update now!!

IPL: Audi 3G 9308 (SH7785) / QNX 6.3.0 [PL_qnx_ipl-3g_9308-sh7785_07412A, built 2007/10/09_12-19-44_UTC]
CPU: SH7785 (>= 5th cut, clk mode 20), 792MHz
RAM: 512 MB (probed, DBCONF=e30002)
FLASH: Spansion S29GL512N: 512 sectors x 256K
FPGA: PL_MMI3G_FPGA_9308_D1_08492A
(0ms)


Entering CLI, type ...

Sorry I didn't understand that you asked for the "scan" command... I will send you if I will be able to launch in IPL cause it immediately starts with the error now.

dead again with error #180

look the memory:

IPL: Audi 3G 9308 (SH7785) / QNX 6.3.0 [PL_qnx_ipl-3g_9308-sh7785_07412A, built 2007/10/09_12-19-44_UTC]
CPU: SH7785 (>= 5th cut, clk mode 20), 792MHz
RAM: 512 MB (probed, DBCONF=e30002)
FLASH: Spansion S29GL512N: 512 sectors x 256K
FPGA: PL_MMI3G_FPGA ...

Miracle!!!!

After that memtest it started and i saw on the screen the fw. v. 022 I tried the update to v. 257 from the SD but no luck when it re-boot to start the update i lost it again.

Sorry, to try to flash an emg-ifs how can I do?
I Did a memory test please look:

ntering CLI, type '?' or 'help' for help


=> help
=> bconf
DBG_IF=scif.ffeb0000.115200.44000000.16
DIP=100
=> bios
BIOS: LZO uncompression to 0x8c000000
BIOS: Start BIOS @ 0x8c000000
closep
=== UNEXPECTED EXCEPTION ...

@Tschako
I did as you suggested but impossible to boot 1c0000 please look:


IPL: Audi 3G 9308 (SH7785) / QNX 6.3.0 [PL_qnx_ipl-3g_9308-sh7785_07412A, built 2007/10/09_12-19-44_UTC]
CPU: SH7785 (>= 5th cut, clk mode 20), 792MHz
RAM: 512 MB (probed, DBCONF=e30002)
FLASH: Spansion S29GL512N: 512 ...

Many thanks CRASH-100, I will do it.

Большое спасибо краш-100, я сделаю это.

Thanks Tschako, I will try the IPL but as I give the boot1c0000 normally it goes in loop with the error message....

NEW ORIGINAL MMI 3GP FW.

Hi guys, i'm here again because I have an Audi 3G 9308 unit with a strange new problem, the unit is quite working for sometimes but after few minutes it begins to re-boot by itself, and if I connect by serial port it Begins A loop like the following One and I CAN not control it:

"IPL: Audi 3G 9308 ...

Hi Sergeynik,
I have a 2010 A5 with the facelift steering wheel retrofitted. I have in fact the iNav button not working and I would buy your LIN converter. Can you address me where to buy it?

Great Forum Great People here

Done revived the broken unit!!

Great Tschako, you were patient and you've really helped me

BTW the unit has all the red lights switched on and a fan at high RPM but it is working.