Technisat - black screen

I have a trouble with Technisat:
Starting tsd.mibstd2.main.root...


-Welcome to TechniBoot-
SVN Rev: 626459
Loading Emergency updater...
J5e.imx6.start: 0x00741B69
J5e.imx6.start: 0x01D41093
J5e.M30.LoadImage.ready: 0x03D92549
J5e.QNX.LoadImage.ready: 0x0CDB3BB4
CPU0: L1 Icache: 512x64
CPU0: L1 Dcache: 512x64 WB
CPU0: L2 Dcache: 4096x64 WB
CPU0: VFP-d32 FPSID=410330c3
CPU0: NEON MVFR0=11110222 MVFR1=00011111
CPU0: 413fc082: Cortex A8 rev 2 600MHz NOALIGN
Loading IFS...decompressing...done


System page at phys:832d5000 user:fc404000 kern:fc404000
Starting next program at vfe05060c
cpu_startnext: cpu0 -> fe05060c
VFPv3: fpsid=410330c3
coproc_attach(10): replacing fe080d90 with fe08054c
coproc_attach(11): replacing fe080d90 with fe08054c
!!!Emergency!!! - Welcome to QNX Neutrino on the Texas Instruments J5 ECO MIBSTD2_MAIN (ARMv7 Cortex-A8 Core)
J5e.QNX.init.ready
Unable to access /dev/name/gns_client
Starting tsd.mibstd2.main.root...
00:00:05.268 [Info] [mcp] [FREQ:20000000]
00:00:05.271 [Info] [mcp] [PERF:0x648c9cf:IO1] J5e.MCP.init.start
00:00:05.286 [Info] [mcproot] CM is restricted



and no more....black screen.

Please help.

How use:
7 - enable imx6 USB and release imx6 from reset
??

Exist some way how connect USB to the unit????

Write compleated root HMI to unit this same SW

I have the same problem.
The same SW is not available -P0359. Can I use HMI from different SW I have available -P0363.

Цитата:

---

Сообщение от vag-flashdaten

I have the same problem.
The same SW is not available -P0359. Can I use HMI from different SW I have available -P0363.

---

try upload by emergency mode file startup than via terminal read and upload hmi

Emergency does not start. I get this message (like on post 1) when emergency is trying to start.

you try reset Update container??

Emergency mode is out of range - all stopped on this message:

Got an exception: socket failed
.
This should not have happened. Your device is now broken. You now own both halves.

Show photo of sticker.

Why??

Вложение 68788

The same question....

Цитата:

---

Сообщение от hrdinaveliky

The same question....

---

Please clear your inbox. I would like to send you PM

Цитата:

---

Сообщение от hrdinaveliky

Why??

---

I wantrd to Check If I have dump file for your device.

Цитата:

---

Сообщение от mobista

I wantrd to Check If I have dump file for your device.

---

And? You have it?
I just got another working unit with 2XX firmware H25. I'm thinking of making a copy of eMMC and putting it to my broken 3XX. Will that work?

Try it now...

Ok. Left that unit on the shelf for a while, now time to get it fixed.

Flashed eMMC with dump from working unit, still the same. Replaced eMMC, still the same.

When jumped two pins on MB, menu comes up but after pressing 2 and restart unit shows log as in post 1 and stops.

Any help will be appreciated.

i have exactly the same fault, problem is on my unit short circuit in MMC i get no vss to mmc, blown transistor

Цитата:

---

Сообщение от chris2011

i have exactly the same fault, problem is on my unit short circuit in MMC i get no vss to mmc, blown transistor

---

Can you show which one?

You get this error when the i.MX is dead, you have to replace the mcimx6d6avt to make the system boot again. The problem is the efuse configuration from the old i.MX, I havent been able to get everything working when replacing the processor.