MHI2 a6 c7 bricked after patch

Hi. I have a problem with mib2 out of a6 c7. I did firmware update from p3634 to k3663, then patched it, and all seemed to be fine. Then I tried to code it with vcp, but it froze during coding. So I tried to code it once more - but unit was not responding. I reset mib just to see a blank screen for over a minute, then I showed "radio initializing" and it stuck. I could not connect to it with vcp, with putty I can only connect on mmx, rcc doesn't respond. I thought I could restore backup I did, but when I go for "on -f rcc flash it -v -a 0x00540000 -d -f /net/mmx/fs/sda0/original-ifs-root-both.ifs" putty says "rcc: host is down". Same result when I try to manualy change dir to /net/rcc. How to recover it? Now, I can do it on bench only, as I removed it from the car.

I can fix your unit but not remote.

p.s. Keep using the "free" solutions ... more will come.

I have it on quadlock, rcc responds, however only on ipl mode, without shorting tx and ground is dead. Breaks fine but after 10 seconds runs further. Can you help? Here's the log.

IPL: A239 C0,16153A[2016-04-13 13:39:22],J5,PG3.0,GL-S=64(0),RAM=128,RST=9
CLK: 720/600/400 MHz (ARM/DSP/DDR)
IOC: 4e33427e 7e7e7e7e 7e7e414e 7e7e7e00
BREAK detected - press any key to stop the ipl within 5000ms! => BREAK accepted! 1


Entering CLI [?], type '?' for help


=> help
Please enter one of the following commands
b115200 - set baudrate for ser1 to 115200
b460800 - set baudrate for ser1 to 460800
b921600 - set baudrate for ser1 to 921600
bconf - alias for 'printenv'
bios - alias for 'boot -t BIOS ...'
boot - boot sequence
crc32 - compute BG CRC32 over memory region
dsp - reset and boot the DSP
dspl - dump dsp loader args
echo - print arguments to console
eraseit - flash erase
flashit - flash update
fscan - scan NOR flash
getenv - set environment variables
go - jump to 'addr'
help - show available commands and help on the latter.
hwconf - dump hardware configuration
ioc_mode - read IOC boot mode (SPI)
iplver - show IPL status / version
memboot - boot image(s) from memory
memperf - memory performance test (benchmark)
memtest - memory test
mt - alias for 'memtest'
printenv - display environment variables and their content
qboot - alias for 'boot -t QNX ...'
rz - alias for 'zmodem'
sboot - start boot table via DSP loader
setenv - set an environment variable or change its value
tstamps - dump time stamps
unsetenv - set environment variables
zmodem - download img over serial line (Z-Modem protocol)
=>
IPL: A239 C0,16153A[2016-04-13 13:39:22],J5,PG3.0,GL-S=64(0),RAM=128,RST=9
CLK: 720/600/400 MHz (ARM/DSP/DDR)
IOC: 4e33427e 7e7e7e7e 7e7e414e 7e7e7e00
fb2:ARM=8020000/2
*** WARNING: Enabling DSP access to the entire RAM!
ipl done
Startup: PL_qnx_startup-jacinto5-v7_Dev_MibJ5_13372A, built 2013/09/10_12-21-17_UTC
Library: [DATE=2013/02/01-08:07:42-WEST USER=MHupfer HOST=oekan402]
Board: 0000a239.000000c0
Command: -vvvv -p2000 -x 0xc2700000,0x01900000 -x 0x86700000,0x01900000 -wb
========================================
IFS: ver.300003b5 (type=3)
UMEM: 08000000-0bffffff(F) 80000000-87ffffff(R)
ENV: @40313fa0 "IOC_BOOTMODE=N3B~~~~~~~AN~~~
IOC_BM_INFO=0x40313a8c,0x10
HW_REV=A239 C0,0x19,J5,PG3.0
LAST_RST=0x0009
"
<8003> 39 a2 c0 00
DSPLOAD DATA: 838c0400 (1024)
========================================
RAM: 128 MB
FLASH: 64 MB @0x08000000
Allocing from c2700000 for 01900000
Allocing from 86700000 for 01900000
dsp_mem_count= 00000002
delaying 2000 ms for various bugs
delaying done
in pcie_init_delay
Polling for clock
pcie clock detected after delaying for approx. 1 usec.
PCIe function could be enabled
DSP: loader c674x_ipl_T10 (May 6 2015 09:47:23), args @838c0400 (1024)
Added GPIO-callouts
CPU0: L1 Icache: 512x64
CPU0: L1 Dcache: 512x64 WB
CPU0: L2 Dcache: 8192x64 WB
CPU0: VFP 410330c3
CPU0: 413fc082: Cortex A8 rev 2 600MHz
Setting GPIO 0
Setting GPIO0_FAL to 00001000
Setting GPIO0_RIS to 00000004
Setting GPIO 2
Setting GPIO2_INTSET0 to 00004000
Setting GPIO2_INTSET1 to 00010000
DSP loader failed: 4294963095

Dont matter, unit retrieved

Hi.
I need help. MHI2 bricked after conversion CN to EU. All back to alive without connection with 5F. I tried everthing emergency update reflash etc.
Any sugestions ?
​THX for help

Which one connection method U lost?