Turbo Quattro

**onyx4** » Вт авг 11, 2020 11:47 am

aleka писал(а):mmx_fs0 is enough.
After device founding via JTAG you also need cut off BCT file from dump mmx_fs0 in 0 to 17EF adresses, then load this BCT file to MIB with help of TegraRCM https://github.com/NVIDIA/tegrarcm . It work via USB.

[ATTACH=CONFIG]68662[/ATTACH]

https://turbo-quattro.com/showthread.ph ... post642033

Hi,
Can you help me with connect tegrarcm.I'm not a Linux user

Where to place the folder with tegrarcm and how to run it.
I will be happy for any advice.
Thanks a lot
Onyx4

**eprst** » Пт май 15, 2020 9:53 pm

flash or emms?

**hrdinaveliky** » Пт май 15, 2020 9:48 pm

No..

**eprst** » Пт май 15, 2020 8:58 pm

Flash mx29gl128flt2s + MTFC8GACAEDQ
You read processor?

**hrdinaveliky** » Пт май 15, 2020 8:49 pm

I found only: NXP MCIMX6D6

Address for RAMM?? Size 32 KB??

Base Address??

Type of Flash Memory??

**eprst** » Пт май 15, 2020 8:39 pm

MCIMX6D6AVT10AD

**hrdinaveliky** » Пт май 15, 2020 8:36 pm

How setup j-link??

Type of mcu??

**hrdinaveliky** » Пт май 15, 2020 8:34 pm

Thanks a lot!!

**eprst** » Пт май 15, 2020 8:23 pm

you are welcome))

**eprst** » Пт май 15, 2020 3:52 pm

please give me the files you read

**hrdinaveliky** » Пт май 15, 2020 2:10 pm

The same motherboard:
https://turbo-quattro.com/showthread.ph ... post641073

**hrdinaveliky** » Пт май 15, 2020 2:08 pm

ZR from PREH....the side??

**eprst** » Пт май 15, 2020 1:58 pm

please photo your board Technisat

**hrdinaveliky** » Пт май 15, 2020 1:39 pm

Yes please jtag no sd-card connection.

**eprst** » Пт май 15, 2020 1:19 pm

photo board?

**hrdinaveliky** » Пн май 11, 2020 2:13 pm

Could you share??

**mobista** » Пн май 11, 2020 1:45 pm

hrdinaveliky писал(а):How connect jtag to Technisat???

What for?

**hrdinaveliky** » Вс май 10, 2020 2:31 pm

How connect jtag to Technisat???

**onyx4** » Чт апр 30, 2020 10:27 pm

Thank you for help me ,
I'm waiting for the hardware then I'll try

**aleka** » Пт апр 24, 2020 8:25 pm

mmx_fs0 is enough.
After device founding via JTAG you also need cut off BCT file from dump mmx_fs0 in 0 to 17EF adresses, then load this BCT file to MIB with help of TegraRCM https://github.com/NVIDIA/tegrarcm . It work via USB.

Вложение USB.jpg больше недоступно

https://turbo-quattro.com/showthread.ph ... post642033

Turbo Quattro

MMX restore - HELP

Ответить

Развернуть Обзор темы: MMX restore - HELP