востановление поврежденных голов +/ damage head unit repair [Архив] - Страница 2

Tschako

03.12.2014, 03:12

9308_boot_log:

BIOS: No packet found!
IPL: Audi 3G 9308 (SH7785) / QNX 6.3.0 [PL_qnx_ipl-3g_9308-sh7785_08253A, built 2008/06/18_15-16-25_UTC]
CPU: SH7785 (>= 5th cut, clk mode 20. 4xDDR), 792MHz
RAM: 512 MB (probed, DBCONF=e30002)
FLASH: Spansion S29GL512N (32bit): 512 sectors x 256K
FPGA: PL_MMI3G_FPGA_9308_D1_09324A
(0ms)
*** Old-fashioned mark found on IFS @0x1c0000: .zero=0x3000001e
*** Old-fashioned mark found on IFS @0x780000: .zero=0x10000000
starting image @780000 ...

Ð*]Ø¹tup: PL_qnx_startup-sh7785_08362A, built 2008/09/02_07-53-12_UTC
RAM : 128 MB @0x08000000
RAM : 128 MB @0x40000000
NVRAM: 28 MB @0x5e400000
RAM : 228 MB @0x50000000
FLASH: 128 MB @0x00000000

System page at phys:0800a000 user:0800a000 kern:8800a000
Starting next program at v8804aa20
Welcome QNX6.3.2 (QNXLabel RL_qnx_os_632_PSP3_08041A)- Harman/Becker MMI3G Build 9307/08 D1-10291A
s: 0
v: 0
r: 0
m: 0
mkprocsymlinks 0.10, reading /mnt/ifs-root/etc/system/efs_symlinks.cfg
done
s: 0
v: 0
r: 0
m: 0
mkprocsymlinks 0.10, reading /mnt/ifs-root/etc/system/ifs-root_symlinks.cfg
done
üstarting server starter...
# multicored [000000000.666]:version 4.1.d, verbosity 1 (supported 4), scope 0x00000001, console: /dev/ser1 (fd=3), FILE_LOGGING, TESTCONTROL
multicored [000000000.698]:udp: broadcaster created
multicored [000000000.701]:attached to filesystem at /hbsystem/multicore, port 851
multicored [000000000.705]:MACHINE:SH(1), total MEM 507510784, 1: 271582976 SH7785 (SH4A) 792MHz, FPU
multicored [000000000.709]:sloop active
multicored [000000000.710]:lo0 127.0.0.1 255.0.0.0
NVLOADER: Booting DSP (DRAM Setup time = 1000 us)...
NVLOADER: Going to call nvTsrmRawLoad for file /etc/NvDspCodecs.elf
NVLOADER: Done
Enabling DMA using channel 7
Overriding default Interrupt Priority
Current debug level = 0x7fffffff
dmaChannel = 7, interrupt thread priority = 21
multicored [000000001.214]:listener on port 851 active, fd=7
devg-NVMEM: Mapped vaddr 0x38100000 to paddr 0x5c487000
dev-nvram: PL_qnx_dev-nvram_07225A, built 2007/06/01_15-44-08_UTC
dev-nvram: page_size:4096
dev-nvram: signalling register 10ee:9308:0:40:40 [vid:did:bar:offs:mask]
dev-nvram: CPU: SH7785 (5th cut or higher, clk_mode 20) [10300700:250, 133735fa]
dev-nvram: map '/dev/nvram/navi' to 0x5e400000-0x5fffefff
dev-nvram: map '/dev/nvram/.guard' to 0x5ffff000-0x5fffffff
dev-nvram: SelfRefresh was inactive
UART: Mod:0E Date:08511A Ver:2.2.1
devc-ser8250hb: UART supports FiFo counter
devc-ser8250hb: UART supports 32bit access
devc-ser8250hb: RX_FIFO_SIZE:512 TX_FIFO_SIZE:512
devc-ser8250hb: set IBUF size to 4096
UART: Mod:0E Date:08511A Ver:2.2.1
devc-ser8250hb: UART supports FiFo counter
devc-ser8250hb: RX_FIFO_SIZE:32 TX_FIFO_SIZE:32
UART: Mod:0E Date:08511A Ver:2.2.1
devc-ser8250hb: UART supports FiFo counter
devc-ser8250hb: RX_FIFO_SIZE:32 TX_FIFO_SIZE:32
WARNING: NON PERFORMANT MODULAR STARTUP!!!
Debug filehandle = 4
For further debug messages have a look at multicore output consoles '/hbsystem/multicore/navi/g'
Mask = c3
GPIO 7 set to = Low
Overriding default Interrupt Priority
TraceClientLogSink#processConfigChanged silent: false
DSIVersion: 0.0.0
DSISource: DSI 2009_49_49
DSI-Build-Version: 30.11.09/v1.138.3
ReleaseLabel: Integration_AU_MMI3G_10070P

io-media-nvidia built: Mar 4 2009 16:48:41 against Official Tree

nv_global.verbose = 0

start JDSI bundle
jdsi.loglevel : 2Virtual Address for CDDA DirectIO = 8394000

No External Component found
stream factory memory mode : classic
dsigen v1.138.3 - core v2.1
prop os.arch : sh4
prop jdsi.3SoftOSGi : true
DSI dispatcher disabled!
NEDL: Acquiring Capture Unit
NEDL: Acquiring Layer
NEDL: Switching source to 0 (Format = PAL)
NvRender: Reconfigure Video Port to PAL
NEDL: Switching source to 0 (Format = PAL)

[MSG]@6136 (77861.161): COnOffPresCtrl::requestSetPowerState(), state: 3
[MSG]@6495 (77861.161): COnOffPresCtrl: IOCBoloMode: 0
[MSG]@6496 (77861.161): -- getHardwareSample: state=2 -- hwSample = 0xd1
[MSG]@6496 (77861.161): -- getHardwareVariant: state=2 -- hwVariant = 0x7
[MSG]@6497 (77861.161): COnOffPresCtrl: newSystemState: 20
[MSG]@6559 (77861.161): +++ PRODUCTION_MODE is 0
[MSG]@6563 (77861.161): +++ remounting of the efs partitions is done, persistency is set to fully operable...
[MSG]@6602 (77861.161): COnOffPresCtrl: newSystemState: 35
NEDL: Switching source to 0 (Format = PAL)
NEDL: Enabling Capture
msgpassing channel opened on /dev/dsi/data
NAVI: sys_alloc_shm_area(/dev/nvram/navi) open() ok: 39
NAVI: sys_alloc_shm_area(/dev/nvram/navi) filesize() = 29356032
NAVI: sys_alloc_shm_area(/dev/nvram/navi) mmap to 50000000
NAVI: sys_alloc_shm_area(/dev/nvram/navi): physical of 50000000 at 5e400000
[MSG]@6958 (77861.161): +++ persistency StartupMode is 1
[MSG]@6990 (77861.161): +++ TEL_SETTINGS_REST is 3
[MSG]@6991 (77861.161): +++ setting BtAvailable to true
[MSG]@6998 (77861.161): +++ ReadInt FLAG_SYSTEM_RESET, Value 1
[MSG]@7007 (77861.161): +++ MISC_HB_REGIONCODE 0
NEDL: Switching source to 0 (Format = NTSC)
NvRender: Reconfigure Video Port to NTSC
NvRender: Starting VIP Video Capture
DSIAddressbook (0) - v10.0G1.138.3
DSIAddressbook (1) - v10.0G1.138.3
DSIAddressbook (2) - v10.0G1.138.3
DSIAddressbook (3) - v10.0G1.138.3
DSIAMFMTuner (0) - v8.0G1.138.3
DSIAudioManagement (0) - v8.1G1.138.3
DSIBluetooth (0) - v4.3G1.138.3
DSIBrowser (0) - v4.0G1.138.3
DSIBrowser (1) - v4.0G1.138.3
DSIBrowser (2) - v4.0G1.138.3
DSICallLists (0) - v3.0G1.138.3
DSICarClimate (0) - v4.0G1.138.3
DSICarComfort (0) - v3.0G1.138.3
DSICarParkingSystem (0) - v2.4G1.138.3
DSICarSuspensionControl (0) - v1.0G1.138.3
DSICarLight (0) - v2.0G1.138.3
DSICarService (0) - v3.2G1.138.3
DSICarDriverAssistance (0) - v2.0G1.138.3
DSICarKombi (0) - v4.4G1.138.3
DSIDABTuner (0) - v5.3G1.138.3
DSIDiagHMIAttribs (0) - v4.0G1.138.3
DSIIconrenderer (0) - v1.0G1.138.3
DSIIconrenderer (1) - v1.0G1.138.3
DSIDataDisplay (0) - v5.0G1.138.3
DSIDisplayManagement (0) - v9.6G1.138.3
DSIInfotainmentRecorder (0) - v2.0G1.138.3
DSIKeyPanel (0) - v2.3G1.138.3
DSIMapViewer (0) - v18.3G1.138.3
DSIMedia (0) - v4.6G1.138.3
DSIMediaRecorder (0) - v1.4G1.138.3
DSIMOSTInfo (0) - v3.0G1.138.3
DSINavigation (0) - v72.0G1.138.3
DSIObexAuthentication (0) - v1.0G1.138.3
DSIPhonoConv (0) - v1.0G1.138.3
DSIPersistence (0) - v10.1G1.138.3
DSIPowerManagement (0) - v3.4G1.138.3
DSIStartup (0) - v1.2G1.138.3
DSIProfileManager (0) - v6.0G1.138.3
DSISDARSTuner (0) - v2.2G1.138.3
DSISMS (0) - v4.1G1.138.3
DSISound (0) - v8.0G1.138.3
DSISSS (0) - v6.2G1.138.3
DSISwdlDeviceInfo (0) - v1.1G1.138.3
DSISwdlLogging (0) - v1.1G1.138.3
DSISwdlProgress (0) - v1.2G1.138.3
DSISwdlSelection (0) - v2.7G1.138.3
DSITelephone (0) - v10.0G1.138.3
DSITIMTuner (0) - v2.3G1.138.3
DSITmc (0) - v9.2G1.138.3
DSITmcOnRoute (0) - v6.0G1.138.3
DSITTS (0) - v4.0G1.138.3
DSITTS (1) - v4.0G1.138.3
DSITunerAnnouncement (0) - v1.0G1.138.3
DSITVTuner (0) - v5.2G1.138.3
DSIVCardExchange (0) - v5.0G1.138.3
DSIWavePlayer (0) - v5.2G1.138.3
DSIWavePlayer (1) - v5.2G1.138.3

Duration of starting JDSIBundle : 3124ms
decoder thread priority : 2000:0 (5)
decoder thread priority : 100:0 (5)

CHBComponentMux.cpp:317: ASSERTION failed

CHBComponentMux.cpp:275: ASSERTION failed
decoder thread priority : 12:0 (5)
[MSG]@7693 (77861.161): +++ HW index: d1 variant: 9307
[MSG]@7709 (77861.161): +++ MISC_HB_REGIONCODE 0
High Nav: 91
decoder thread priority : 9:0 (5)
AS: 2CPS: 3

decoder thread priority : 4:0 (5)
AS: 2
AS: 3
decoder thread priority : 50:0 (5)
AS: 3
decoder thread priority : 24:0 (5)
decoder thread priority : 51:0 (5)
decoder thread priority : 8:0 (9)
AS: 1
AS: 2
decoder thread priority : 7:0 (5)
AS: 3
decoder thread priority : 3:0 (5)
decoder thread priority : 32:0 (5)
The message must not be null or of zero length
decoder thread priority : 20:0 (5)
[pcidma] finished.
Audi-2D library version: 20080626
Using NVIDIA driver
[MSG]@66385 (77861.161): COnOffPresCtrl::requestSetPowerState(), state: 3

zerbino

09.12.2014, 03:05

Товарищи, путём долгих ухищрений удалось сделать usb ttl как доктор прописал. 1 (https://pp.vk.me/c624028/v624028153/52cf/S5zWKXNvLwc.jpg) 2 (https://pp.vk.me/c624028/v624028153/52d8/sqgBNpegmyg.jpg) 3 (https://pp.vk.me/c623219/v623219153/7971/cLIv2fPqBDQ.jpg) Делалось не так для продажи, как для активизации интереса к этой теме. UkNik нарисовал, я же собственноручно резал платы (https://vk.com/video42164153_170790057), паял и тестил. Отлично втыкается сбоку mmi при выломаной железочке. Самое сложное было найти разъём HSEC, заказать и оплатить. Если Сергей Ник посчитает, что я злостный барыга, то я уберу, конечно, это сообщение. Ну и если интересно, пишите в личку. Если у UkNik-а дойдут руки до JTAG, то ещё и закажем платы и распаяем его в будущем, благо разъёмов пришлось заказать 100 штук (sic lol).

Crash-100

09.12.2014, 10:37

Прикольно получилось, интересует цена данного устройства.

spinmar

09.12.2014, 10:50

well done.
I'm interested in the price too.

sergeynik

09.12.2014, 13:15

о и мне нада пусть будет

zerbino

09.12.2014, 22:50

Мужчины) так и хочется в рифму ответить :) Ладно заслуженный картораздаватель Сергей Ник, но вы то видели, что в ЛС просил писать?) Тему то не закакивайте.

дабы не было вопросов и недоумений, я вам хочу сообщить, что только один разъём 20ти контактный стоит 500р.

Timur_ua

19.12.2014, 11:08

А у меня новая незадача ) Хотел китай на европу перешить, залил европейский еепром, поставил в зеленке евро регион, Но, ВЕРОЯТНО, надо было и язык сменить с китая на русский или английский, а я так прошил - зависает на заставке ВВ, на диагностику выходит.... Как язык поменять при старте системы кто то подскажет? может скрипт какой... Или не в этом дело? Могу обратно залить китай еепром и прошить - как то можно заставить ее шиться без терминала? в общем засада )))
Появилось время опять для этой башки. Подключил терминал, загнал в зеленый экран, прошивается, но ничего не происходит - все та же заставка ВВ и все )) Ума не приложу что делать. Так же на диагностику выходит ) Может лог выложить?

Timur_ua

19.12.2014, 11:28

еепром европейский. пробовал обратно китайский заливать и прошивать - дудки...

Timur_ua

19.12.2014, 12:34

вот лог гляньте пож https://cloud.mail.ru/public/b90d7b0cf38f/850.log

Zdenek

20.12.2014, 13:08

Hi,
how to load FPGA emergency without erase head at adress 40000?

I try in IPL command Fpga 100000, but no luck.
thanks

Tschako

20.12.2014, 17:10

The "fpga 100000" command loads only the EMG-fpga in memory ...

- For the 9308 (MMI 3G) put the FW (K0257) SD Card in the 1st SD Slot and start from IPL with "boot 1c0000" in the emergency app.

After the automated loading of the SD Card Driver, then type from the QNX prompt as FOLLOWS:

FlashIt -d -a -f 40000 /mnt/sdcard10t11/MU9308/fpga/41/default/systemFPGA.hbbin

- it comes back with "erasing "," progamming "and" Validating "

- if there is an Other unit type, you have to correct the path from the SD Card

- - good Luck!

Zdenek

20.12.2014, 18:27

its another unit... normal ifs its KO...
I need to first emergency FPGA loaded, then emergency began work on USB, or CD.
Because if I run emergency, not begins boot from CD.
Commands to delete the header FPGA can not enter, because unit start quickly and then stop.
I need EM FPGA load, then boot EM IFS.
Thanks

Tschako

20.12.2014, 18:34

if you start in IPL, then call "fpga 100000" will load the emg-fpga from hex 100000 directly for the sockets.

Then call "boot 1c0000" will load the driver for CD and SD and the emg-app to do your work or start the automated emergency routine directly from the correct SD Card.

Zdenek

20.12.2014, 18:54

I try this, but not work....
its BMW unit and when boot 6dc0000....emergency run, but after a while starts normal ifs and then stop.

In Another unit that works .... can run through diagnosis emergency ...
Then dump begins:
FPGA emergency loaded
start 6dc0000 image ...

The damaged unit but does not communicate diagnostics ....
but it must be a command to load Em FPGA, without deleting the header.

Tschako

20.12.2014, 20:09

OK, I have no experience with the BWM version... But a failure like this could have something todo with a weak memory...
Try to run the mem check for sure...

ДЮК

27.12.2014, 20:03

Привет, корифеи.

Подскажите по такой проблеме:
голова 3ГП убита, как говорят, кривой инсталляцией и активацией карт. Иногда даже загружается юзеринтерфейс, но сразу отключается.

Было желание запустить автовосстановление с помощью широкоизвестной команды flashit -a 40000 -e 1000
но:

IPL: Audi 3G 9308 (SH7785) / QNX 6.3.0 [PL_qnx_ipl-3g_9308-sh7785_08253A, built 2008/06/18_15-16-25_UTC]
CPU: SH7785 (>= 5th cut, clk mode 20. 4xDDR), 792MHz
RAM: 512 MB (probed, DBCONF=e30002)
FLASH: Spansion S29GL512N (32bit): 512 sectors x 256K
FPGA: PL_MMI3G_PLUS_FPGA_9411_D1_11384A (0ms)

Entering CLI, type '?' or 'help' for help

=> flashit -a 40000 -e 1000
Unknown command 'flashit' - try 'help'

jalib

27.12.2014, 20:09

Ну может я ре прав, но 9308 помоему не 3gp. Если пациент грузится и можно войти в зеленое меню, то может emergency repair?

Crash-100

27.12.2014, 20:09

так у тебя же IPL, ты сделай boot ..... и повтори

Crash-100

27.12.2014, 20:11

Ну может я ре прав, но 9308 помоему не 3gp. Если пациент грузится и можно войти в зеленое меню, то может emergency repair?
Ты видишь IPL он у всех одинаковый.

Crash-100

27.12.2014, 20:12

Может у кого есть дамп eeprom от RNS850 europe.

ДЮК

27.12.2014, 20:13

jalib (http://turbo-quattro.com/member.php?6656-jalib)

Я тоже написал и сразу осознал, что мне тоже не нравится 9308.
Но я понятия не имею, как должно выглядеть на 3Г+

ДЮК

27.12.2014, 20:17

Голова не у меня, далеко. Я просто пытаюсь помочь. Пока все мутно, да еще из за корректности перевода могут быть проблемы.
Так все таки, у 3Г+ такая же строчка, про 9308?
Или в голову запихали что то не то? Собственно машина - А8. ХЗ что там в них ставили.
Логи есть: https://www.sendspace.com/file/b1yvlw
И они как бы от 3ГП.

Zdenek

27.12.2014, 21:56

flashit -a 40000 -e 1000 not work in IPL....
Commads work only when normal run or emergency.

ДЮК

28.12.2014, 00:35

flashit -a 40000 -e 1000 not work in IPL....
Commads work only when normal run or emergency.
exactly
completely forgot that this instruction QNX :upset:
We can only boot 1c0000 or 100000?
Or JTAG?

Zdenek

28.12.2014, 00:56

boot 1c0000 and write command "flashit -a 40000 -e 1000"....

a4ss4abt

06.01.2015, 01:35

Hi guys and thanks for this very useful thread. I'm new here and I'm very sorry but I have to write in english cause for me the russian is too much difficult.
Reading this thread from the first post, it wasn't so easy using translators that change the sinthax of QNX commands, but finally i was able to find the solutions.
Now i have just recovered the first one of my two 9498 bricked units
On the second one I did an error erasing the partition dev/fs0p3. I tried with the "flashit -a 40000 -e 1000" without success. The emergency update starts but cannot write the lost partition. I think the partition must be created and mounted but how?
here the first part of Boot log any help will be very apreciated.

IPL: Audi 3G 9308 (SH7785) / QNX 6.3.0 [PL_qnx_ipl-3g_9308-sh7785_08253A, built 2008/06/18_15-16-25_UTC]
CPU: SH7785 (>= 5th cut, clk mode 20. 4xDDR), 792MHz
RAM: 512 MB (probed, DBCONF=e30002)
FLASH: Spansion S29GL512N (32bit): 512 sectors x 256K
FPGA: PL_MMI3G_PLUS_FPGA_9411_D1_11384A (0ms)
*** Old-fashioned mark found on IFS @0x1c0000: .zero=0x30000013
*** Old-fashioned mark found on IFS @0x680000: .zero=0x10000000
starting image @680000 ...

Startup: PL_qnx_startup-sh7785_11292A, built 2011/07/19_08-03-38_UTC
RAM : 128 MB @0x08000000
RAM : 128 MB @0x40000000
NVRAM: 36 MB @0x5dc00000
RAM : 220 MB @0x50000000
FLASH: 128 MB @0x00000000
FPGA IRQ: Interrupt Controller ID:33 Ver:2.1.0 ILVL:7 Lines:255

System page at phys:0800a000 user:0800a000 kern:8800a000
Starting next program at v8804aae0
Welcome QNX6.3.2 (QNXLabel RL_qnx_os_632_PSP3_08041A)- Harman/Becker MMI3GP Build 9498 E1-12321A
USB-stuff (QNXLabel RL_qnx_os_632_PSP3_08041A)
(devf t1::f3s_table_find:247) fs0p3 corrupt U: 74
checkPersistence: /mnt/efs-persist has not been mounted by devf-generic after 30 seconds: formatting /dev/fs0p3
checkPersistence: trying to backup the corrupted flash: ('.' == 1M)
.........
Unable to access "/mnt/efs-persist" (2)
# NV: Waiting for the minirm init done indication file /dev/shmem/nvminirm.finished'
NVLOADER: Booting DSP (DRAM Setup time = 1000 us)...
NVLOADER: Going to call nvTsrmRawLoad for file /etc/NvDspCodecs.elf
NVLOADER: Done
Enabling DMA using channel 11
Overriding default Interrupt Priority
Current debug level = 0x7fffffff
dmaChannel = 11, interrupt thread priority = 21
devg-NVMEM: Mapped vaddr 0x38100000 to paddr 0x5d397000
[pcidma] PL_qnx_pcidma_FMod08363A_09274A, built 2009/07/02_11-10-37_UTC
multicored [000000154.647]:version 4.6.d, verbosity 1 (supported 4), scope 0x00000001, console: /dev/ser1 (fd=3), FILE_LOGGING, TESTCO
NTROL, DYNAMIC_LOAD
multicored [000000154.650]:using 750 buffers of size 1460 (total 1095000 bytes)
multicored [000000154.694]:version 4.6.d, verbosity 2 (supported 4), scope 0x00000001, console: /dev/ser1 (fd=3), FILE_LOGGING, TESTCO
NTROL, DYNAMIC_LOAD
multicored [000000154.716]:udp: broadcaster created
multicored [000000154.722]:attached to filesystem at /hbsystem/multicore, port 851
multicored [000000154.740]:MACHINE:SH(1), total MEM 499122176, 1: 271582976 SH7785 (SH4A) 792MHz, FPU
multicored [000000154.745]:sloop active
multicored [000000154.747]:lo0 127.0.0.1 255.0.0.0
multicored [000000154.747]flog0 0.0.0.0 0.0.0.0
multicored [000000154.774]:listener_activate()
multicored [000000154.776]:listener on port 851 active, fd=7
Mask = c3
GPIO 7 set to Low
Overriding default Interrupt Priority
dev-nvram: PL_qnx_dev-nvram_07225A, built 2007/06/01_15-44-08_UTC
dev-nvram: page_size:4096
dev-nvram: signalling register 10ee:9411:0:40:40 [vid:did:barffs:mask]
dev-nvram: CPU: SH7785 (5th cut or higher, clk_mode 20) [10300700:250, 133735fa]
dev-nvram: map '/dev/nvram/navi' to 0x5dc00000-0x5fffefff
dev-nvram: map '/dev/nvram/.guard' to 0x5ffff000-0x5fffffff
dev-nvram: SelfRefresh was inactive
UART: Mod:0E Date:09503A Ver:2.2.2
devc-ser8250hb: UART supports FiFo counter
devc-ser8250hb: UART supports 32bit access
devc-ser8250hb: RX_FIFO_SIZE:2048 TX_FIFO_SIZE:2048
devc-ser8250hb: set IBUF size to 16384
UART: Mod:0E Date:09503A Ver:2.2.2
devc-ser8250hb: UART supports FiFo counter
devc-ser8250hb: UART supports 32bit access
devc-ser8250hb: RX_FIFO_SIZE:512 TX_FIFO_SIZE:512
UART: Mod:0E Date:09503A Ver:2.2.2
devc-ser8250hb: UART supports FiFo counter
devc-ser8250hb: RX_FIFO_SIZE:32 TX_FIFO_SIZE:32
Debug filehandle = 5
For further debug messages have a look at multicore output consoles '/hbsystem/multicore/navi/g'
[pcidma] PL_qnx_pcidma_FMod08363A_09441A, built 2009/10/26_07-46-16_UTC
mam0 available
NAVI: sys_alloc_shm_area(/dev/nvram/navi) open() ok: 9
NAVI: sys_alloc_shm_area(/dev/nvram/navi) filesize() = 37744640
NAVI: sys_alloc_shm_area(/dev/nvram/navi) mmap to 38100000
NAVI: sys_alloc_shm_area(/dev/nvram/navi): physical of 38100000 at 5dc00000
NV_ENABLE_DYNAMIC_PRIORITIES is enabled
max-consecutive-errors set to 2
timeout retries config string == |2|
timeout-retries set to 2
io-media-nvidia built: Jul 20 2012 14:33:47 against Official Tree
nv_global.verbose = 0
Virtual Address for CDDA DirectIO = 842F000
0,"nVAudio_init: IN
0,"nVAudio_class_init: IN
nVAudio_class_init: OUT success
0,"nvidia_render_manager_init();
0,"nVAudio_init: IN
0,"nVAudio_class_init: IN
nVAudio_class_init: OUT success
0,"nVAudio_class_init: IN
nVAudio_class_init: OUT success
io-media-nvidia/a2dp_player: The 'metadata-timeout' setting is missing or has an invalid value, defaulting to 4000ms
0,"nVAudio_init: IN
0,"nVAudio_class_init: IN
nVAudio_class_init: OUT success
0,"nvidia_render_manager_init();
0,"nVAudio_init: IN
[t(p) usr/sbin/io-display 98332 7 10 7033aaf6]
[t(c) usr/sbin/io-display 98332 5 10 70334f72]
WARNING: NON PERFORMANT MODULAR STARTUP!!!
Path=0 - XILINX ATAPI
target=0 lun=0 CD-ROM(5) - FJ-TEN DVD-ROM DV-05FT2 Rev: 1B20
Path=1 - XILINX ATAPI
target=1 lun=0 Direct-Access(0) - TOSHIBA MK6050GA Rev: TJ10
cd0 mounted after 1 try
[t(p) proc/boot/procnto-instr 1 8 10 8803cc12]
[t(c) ./MMI3GNavigation 155689 23 10 703351de]
***************************************
*** ***
*** Online Speech ***
*** ***
*** EncodeStream ***
*** v1.0.02 ***
*** ***
***************************************
DSIVersion: 0.0.0
DSISource: DSI 2012_26_26
DSI-Build-Version: Mon Jun 25 11:24:44 CEST 2012 / DSIGEN v1.138.4
ReleaseLabel: Int_AU3G_EU_SOP9_12272P
start JDSI bundle
HBTRACE: jdsi.verboselevel = null => verbose-level = 0 because property not set or invalid
jdsi.loglevel : 2
No External Component found
.......................

Tschako

06.01.2015, 01:49

You have to rewrite the efs-persist image in emg-app mode like following this steps:

1. Prepare a SD card with an binary image file from an ifs-persist partition (name: efs-persist.bin)
2. Put SD card in slot #1 (sdcard10t11)
3. start unit in IPL mode
4. enter command "boot 1c0000" to boot emg-app
5. enter command "echo dummy > /HBpersistence/DeveloperMode" to extend the timeout for watchdog reboot
6. enter "flashit -a 6200000 -d -f /mnt/sdcard10t11/efs-persist.bin" to flash the partition image
7. reboot the unit after the verification message
8. the unit now will recover the details for the persistence partition
Thats it!

a4ss4abt

06.01.2015, 01:59

Many thanks Tschako, sorry but you say this :1
what do you mean? I did "boot 1c0000" but w/o success

a4ss4abt

06.01.2015, 02:00

Sorry I missed the second part of the post,
thanks a lot I TRY IMMEDIATLY

Tschako

06.01.2015, 02:05

The "boot 1c0000" command starts the emg-app from IPL mode. Only in IPL mode the "boot" command works!
You have to make sure, to recognize to be in IPL! Only when the prompt lookes like this mark "=>" you are in IPL mode. (Initial Program Loader)
otherwise, you´are not reaching the IPL correctly and the "boot" command doesn´t work.

a4ss4abt

06.01.2015, 02:26

yes, i know IPL mode but i'm trying and cannot give the "echo dummy > /HBpersistence/DeveloperMode" look please:

IPL: Audi 3G 9308 (SH7785) / QNX 6.3.0 [PL_qnx_ipl-3g_9308-sh7785_08253A, built 2008/06/18_15-16-25_UTC]
CPU: SH7785 (>= 5th cut, clk mode 20. 4xDDR), 792MHz
RAM: 512 MB (probed, DBCONF=e30002)
FLASH: Spansion S29GL512N (32bit): 512 sectors x 256K
FPGA: PL_MMI3G_PLUS_FPGA_9411_D1_11384A (0ms)

Entering CLI, type '?' or 'help' for help

=> boot 1c0000
starting image @801c0000 ...

Startup: PL_qnx_startup-sh7785_09332A, built 2009/08/11_11-10-29_UTC
RAM : 128 MB @0x08000000
RAM : 128 MB @0x40000000
RAM : 256 MB @0x50000000
FLASH: 128 MB @0x00000000
FPGA IRQ: Interrupt Controller ID:33 Ver:2.1.0 ILVL:7 Lines:255

System page at phys:0800a000 user:0800a000 kern:8800a000
Starting next program at v88046b20
intrentry_base = 8ffe5630, size=2176
copying intrentry code:
intrentry_code_buf = 88085f28
intrentry_base = 8ffe5630
copy_size = 2432
final intrentry_base = 8ffe5630, size=2176
------------------------------------------------------
Welcome to QNX 6.3.2 (RL_qnx_os_632_PSP3_09423A) MMI3G Audi EMERGENCY SETUP 10214A
starting pci driver
*** init FPGA registers ***
[pcidma] PL_qnx_pcidma_FMod08363A_09274A, built 2009/07/02_11-10-37_UTC
starting dev-ipc for IOC
initialize IPC Driver
starting network driver
starting atapi driver - setup device /dev/cam0
starting devc-pty
Path=0 - XILINX ATAPI
target=0 lun=0 CD-ROM(5) - FJ-TEN DVD-ROM DV-05FT2 Rev: 1B20
Path=1 - XILINX ATAPI
target=1 lun=0 Direct-Access(0) - TOSHIBA MK6050GA Rev: TJ10
starting flash driver
starting SDCard driver
Path=0 -
target=0 lun=0 Direct-Access(0) - SL08G Rev: 8.0
Unable to access "/dev/io-net/en5" (2)
starting with no network driver
================================================== =========
Emergency IFS is started. Emergency app tries to restore
the application.
================================================== =========
49169 running /usr/bin/devg-NVTIRM
DMA is Disabled
dma disabled, interrupt thread priority = 100
49171 running /sbin/io-media-nvidia
49172 running /usr/sbin/io-display
49173 running /usr/apps/MMI3GEmergencyApp
================================================== =========
Emergency shell started, fix your system and restart again
================================================== =========
discplayer_init: IN
nvidia_render_manager_init: IN
INvmRenderManager::GetNvmRenderManager (&pRenderManager);
er = pRenderManager->Init(oConfig);
# App FPGA valid 1
Emergency FPGA valid 1
Disabling IOC watchdog

EmergencyApp-MMI3G: version 31.19.2098, date of build 08.09.2009
pRenderManager->Open()
nvidia_render_manager_init: OUT
discplayer_init: OUT
discplayer_init
discplayer_init: IN
nvidia_render_manager_init: IN
nvidia_render_manager_init: OUT
discplayer_init: OUT
dvdtrackplayer_init
discplayer_init: IN
nvidia_render_manager_init: IN
nvidia_render_manager_init: OUT
discplayer_init: OUT
dvdnavigator_init
created navigator control point with 8249288
mixer_init: IN
mixer_init: OUT
NvTRACELEVEL set to 3 (Level Info)
nVAudio_init: IN
nvidia_render_manager_init();
nvidia_render_manager_init: IN
nvidia_render_manager_init: OUT
nVAudio_init: OUT
installing audio decoders
installing video decoders
nVAudio_init: IN
nvidia_render_manager_init();
nvidia_render_manager_init: IN
nvidia_render_manager_init: OUT
nVAudio_init: OUT
OnIpcGetCaptureUnitSourceCount
Number of displays: 6
Number of layers: 9
Graphics init was successfull: DisplaySize is 800x 480
The FPGA for the application is valid!
Emergency application will do nothing!
result of running command start_efs_driver.sh is 0
(devf t1::f3s_table_find:247) fs1p3 corrupt U: 74
Wait for HBpersistence...
Wait for HBpersistence...
Wait for HBpersistence...
Wait for HBpersistence...
Wait for HBpersistence...
Wait for HBpersistence...
Wait for HBpersistence...
Wait for HBpersistence...
Wait for HBpersistence...
Wait for HBpersistence...
HBpersistence is not available!
************************************************** *********
** DeveloperMode is off!!!! **
** The system will shutdown soon! **
** DO NOT FLASH WITH SCRIPTS IN THIS MODE!!! **
************************************************** *********
** You can enable DeveloperMode like this: **
** echo dummy > /HBpersistence/DeveloperMode **
************************************************** *********
Set DisplayStatus to 2
Set DisplayStatus to 4
Set DisplayStatus to 6
OnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0
OnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0
OnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0
OnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0
OnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0
OnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0
OnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0
OnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0
OnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0
OnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0
OnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0
OnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0
OnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0
OnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0
OnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0
OnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0
OnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0
OnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0
OnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0
OnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0
OnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0
echo dummy > /HBpersistence/DeveloperModeOnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0
OnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0
echo dummy > /HBpersistence/DeveloperModeOnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0

a4ss4abt

06.01.2015, 02:30

it tells me
"no such file or directory"
when i give the command
after it stops the unit

a4ss4abt

06.01.2015, 03:11

did you see this message:

"Emergency application will do nothing!
result of running command start_efs_driver.sh is 0
(devf t1::f3s_table_find:247) fs1p3 corrupt U: 74"

Without the HBpersistence developer mode I cannot give the flashit anyway i'tried but it gave me
"flashit -a 6200000 -d -f /mnt/sdcard10t11/efs-persist.binflashit: can't open /mnt/sdcard10t11/efs-persist.bin: No such file or directory"

here the log
IPL: Audi 3G 9308 (SH7785) / QNX 6.3.0 [PL_qnx_ipl-3g_9308-sh7785_08253A, built 2008/06/18_15-16-25_UTC]
CPU: SH7785 (>= 5th cut, clk mode 20. 4xDDR), 792MHz
RAM: 512 MB (probed, DBCONF=e30002)
FLASH: Spansion S29GL512N (32bit): 512 sectors x 256K
FPGA: PL_MMI3G_PLUS_FPGA_9411_D1_11384A (0ms)

Entering CLI, type '?' or 'help' for help

=> boot 1c0000
starting image @801c0000 ...

Startup: PL_qnx_startup-sh7785_09332A, built 2009/08/11_11-10-29_UTC
RAM : 128 MB @0x08000000
RAM : 128 MB @0x40000000
RAM : 256 MB @0x50000000
FLASH: 128 MB @0x00000000
FPGA IRQ: Interrupt Controller ID:33 Ver:2.1.0 ILVL:7 Lines:255

System page at phys:0800a000 user:0800a000 kern:8800a000
Starting next program at v88046b20
intrentry_base = 8ffe5630, size=2176
copying intrentry code:
intrentry_code_buf = 88085f28
intrentry_base = 8ffe5630
copy_size = 2432
final intrentry_base = 8ffe5630, size=2176
------------------------------------------------------
Welcome to QNX 6.3.2 (RL_qnx_os_632_PSP3_09423A) MMI3G Audi EMERGENCY SETUP 10214A
starting pci driver
*** init FPGA registers ***
[pcidma] PL_qnx_pcidma_FMod08363A_09274A, built 2009/07/02_11-10-37_UTC
starting dev-ipc for IOC
initialize IPC Driver
starting network driver
starting atapi driver - setup device /dev/cam0
starting devc-pty
starting flash driver
Path=0 - XILINX ATAPI
target=0 lun=0 CD-ROM(5) - FJ-TEN DVD-ROM DV-05FT2 Rev: 1B20
Path=1 - XILINX ATAPI
target=1 lun=0 Direct-Access(0) - TOSHIBA MK6050GA Rev: TJ10
starting SDCard driver
Path=0 -
target=0 lun=0 Direct-Access(0) - SL08G Rev: 8.0
Unable to access "/dev/io-net/en5" (2)
starting with no network driver
================================================== =========
Emergency IFS is started. Emergency app tries to restore
the application.
================================================== =========
49169 running /usr/bin/devg-NVTIRM
DMA is Disabled
dma disabled, interrupt thread priority = 100
49171 running /sbin/io-media-nvidia
49172 running /usr/sbin/io-display
49173 running /usr/apps/MMI3GEmergencyApp
================================================== =========
Emergency shell started, fix your system and restart again
================================================== =========
discplayer_init: IN
nvidia_render_manager_init: IN
INvmRenderManager::GetNvmRenderManager (&pRenderManager);
er = pRenderManager->Init(oConfig);
# App FPGA valid 1
Emergency FPGA valid 1
Disabling IOC watchdog

EmergencyApp-MMI3G: version 31.19.2098, date of build 08.09.2009
pRenderManager->Open()
nvidia_render_manager_init: OUT
discplayer_init: OUT
discplayer_init
discplayer_init: IN
nvidia_render_manager_init: IN
nvidia_render_manager_init: OUT
discplayer_init: OUT
dvdtrackplayer_init
discplayer_init: IN
nvidia_render_manager_init: IN
nvidia_render_manager_init: OUT
discplayer_init: OUT
dvdnavigator_init
created navigator control point with 8249288
mixer_init: IN
mixer_init: OUT
NvTRACELEVEL set to 3 (Level Info)
nVAudio_init: IN
nvidia_render_manager_init();
nvidia_render_manager_init: IN
nvidia_render_manager_init: OUT
nVAudio_init: OUT
installing audio decoders
installing video decoders
nVAudio_init: IN
nvidia_render_manager_init();
nvidia_render_manager_init: IN
nvidia_render_manager_init: OUT
nVAudio_init: OUT
OnIpcGetCaptureUnitSourceCount
Number of displays: 6
Number of layers: 9
Graphics init was successfull: DisplaySize is 800x 480
The FPGA for the application is valid!
Emergency application will do nothing!
result of running command start_efs_driver.sh is 0
(devf t1::f3s_table_find:247) fs1p3 corrupt U: 74
Wait for HBpersistence...
Wait for HBpersistence...
Wait for HBpersistence...
Wait for HBpersistence...
Wait for HBpersistence...
Wait for HBpersistence...
Wait for HBpersistence...
Wait for HBpersistence...
Wait for HBpersistence...
Wait for HBpersistence...
echo dummy > /HBpersistence/DeveloperModeHBpersistence is not available!
************************************************** *********
** DeveloperMode is off!!!! **
** The system will shutdown soon! **
** DO NOT FLASH WITH SCRIPTS IN THIS MODE!!! **
************************************************** *********
** You can enable DeveloperMode like this: **
** echo dummy > /HBpersistence/DeveloperMode **
************************************************** *********
Set DisplayStatus to 2
Set DisplayStatus to 4
Set DisplayStatus to 6
OnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0

echo dummy > /HBpersistence/DeveloperMode
No such file or directory

# OnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0
OnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0
OnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0

# echo dummy > /HBpersistence/DeveloperModeOnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0
No such file or directory
# echo dummy > /HBpersistence/DeveloperModeOnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0

OnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0

No such file or directory

# echo dummy > /HBpersistence/DeveloperModeOnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0
OnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0
OnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0

No such file or directory
# echo dummy > /HBpersistence/DeveloperModeOnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0
OnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0

No such file or directory
# echo dummy > /HBpersistence/DeveloperModeOnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0
OnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0

echo dummy > /HBpersistence/DeveloperMode
No such file or directory

echo dummy > /HBpersistence/DeveloperMode
No such file or directory
# OnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0
OnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0
echo dummy > /HBpersistence/DeveloperMode
No such file or directory
#
flashit -a 6200000 -d -f /mnt/sdcard10t11/efs-persist.bin
flashit: can't open /mnt/sdcard10t11/efs-persist.bin: No such file or directory

Tschako

06.01.2015, 03:12

Yes, the reason is quite simple: the HBpersistence is the mounted name for the efs-persist partition. (sorry, I forget)
Means, you have to enter the flashit command string ASAP, or better you try to boot the main app with "boot 680000" and then type the flashit command string I tell you, ASAP.

But normally, if you type in the command as fast as possible, the time will fit to process the flashit work...

By the way, the SD Card with the efs-persist.bin must in the Slot if you start the emg-app.
Otherwise there is no detection given.

Thats what the response to the flashit command tells:
"flashit: can't open /mnt/sdcard10t11/efs-persist.bin: No such file or directory"

Or the mounted name of the SD Card is different. Try to figure out the name, by enter the "mount" or "df" command!
Keep of the complete path of the file located on the card. For this command it must be in root of the SD card.

a4ss4abt

06.01.2015, 04:16

But when you talk about the SD Card do you mean With a firmware complete ? In my case the unit was at 612 version.
here the commands you suggest

HBpersistence is not available!
************************************************** *********
** DeveloperMode is off!!!! **
** The system will shutdown soon! **
** DO NOT FLASH WITH SCRIPTS IN THIS MODE!!! **
************************************************** *********
** You can enable DeveloperMode like this: **
** echo dummy > /HBpersistence/DeveloperMode **
************************************************** *********
Set DisplayStatus to 2
Set DisplayStatus to 4
Set DisplayStatus to 6
OnOff: process IPC event HWsample 225
#
# flashit -a 6200000 -d -f /mnt/sdcard10t11/efs-persist.bin
flashit: can't open /mnt/sdcard10t11/efs-persist.bin: No such file or directory
# OnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0
dfOnOff: process IPC event HWsample 225 HWvariant 198 FinalShutdown 0

/dev/fs1p2 75264 71885 3378 96% /mnt/efs-system
/dev/fs1p1 24064 11 24052 1% /mnt/efs-extende
/dev/sdcard10t11 15507456 2765760 12741696 18% /mnt/sdcard10t11
/dev/sdcard10 15523840 15523840 0 100%
/dev/hd0 2088387 2088387 0 100% /dev/hd0t187.4
/dev/hd0 4273227 4273227 0 100% /dev/hd0t187.3
/dev/hd0 353367 353367 0 100% /dev/hd0t187.2
/dev/hd0 337302 337302 0 100% /dev/hd0t187.1
/dev/hd0 10490382 10490382 0 100% /dev/hd0t187
/dev/hd0 2136645 2136645 0 100% /dev/hd0t79
/dev/hd0 39857265 39857265 0 100% /dev/hd0t78
/dev/hd0 57673287 57673287 0 100% /dev/hd0t77
/dev/hd0 117210240 117210240 0 100%
/dev/cd0 0 0 0 100%

mount

/dev/fs1p2 on /mnt/efs-system type flash
/dev/fs1p1 on /mnt/efs-extended type flash
/dev/sdcard10t11 on /mnt/sdcard10t11 type dos (fat32)

a4ss4abt

06.01.2015, 05:39

it's strange because if i search on the SD with the firmware the file efs-persist.bin I cannot find it
where should it be exactly?

Tschako

06.01.2015, 23:43

a4ss4abt

07.01.2015, 01:21

Oh many thanks Tschako and forgive my ignorance please!!

How to extract it is the problem because the only fully functional main unit I have is mounted on my personal car.

BTW is there any script via SD card that I can use to extract efs-persist.bin w/o unmount my unit?

The firmware version of the unit is important or irrelevant?

a4ss4abt

07.01.2015, 03:13

Looking in my lab, I've found my old 9307 3G unit (not 3GP) which should be fully functional, can I do the extraction from there or should it be mandatory a 9498 unit?

Tschako

07.01.2015, 18:41

It makes sens, to strip an actual Version of the image from an identical maschine type 9498. It is no problem to do it by a SD script. It takes only around minutes to backup the efs-persist partition from the flash. The command ist given above. Add the SD mounting routine as known in any other script.

a4ss4abt

08.01.2015, 03:02

Great Forum Great People here :cool:

Done revived the broken unit!!

Great Tschako, you were patient and you've really helped me :tennis:

BTW the unit has all the red lights switched on and a fan at high RPM but it is working.

Tschako

08.01.2015, 20:16

OK, great! Thats fine!
The efs-persist partition had a couple of backup and secure functions. Maybe it needs a couple of time and restards to fullfill all register with the correct data.
Try to use it a couple of hours, than do a firmware update completely to a higher or same version. This flushes the registers and buffers and gives a new setup base.

Timur_ua

20.01.2015, 13:34

продолжаю пытаться поднять китайца который после вливания еепром европа + прошивка показывает заставку и все. на диагностику выходит. После всем известной команды грузится с СД карты и вновь то же самое. вот лог посмотрите пож:
https://cloud.mail.ru/public/f5ba67f00fbf/850

Timur_ua

20.01.2015, 13:40

ввел команду boot 10..... - djn Graphics init was successfull: DisplaySize is 800x 480The FPGA for the application is valid!
Emergency application will do nothing!
result of running command start_efs_driver.sh is 0
подскажите чего ей не хватает

Timur_ua

20.01.2015, 13:43

вот это смущает после перезагрузки
Using NVIDIA driver
dumping error log: /errlog/error_7185-001.zip
dumping error log: /errlog/error_7185-002.zip
de.audi.atip.error.FatalSystemError: critical HMI error during SMI processing

Nobody_Knows

03.02.2015, 12:00

Timur_ua

05.02.2015, 16:53

Спасибо тебе добрый человек!!! Заработало )

eprst

08.02.2015, 21:15

Привет Всем, обновлял тут карты на 3G+, стал активировать, отвлекли, в итоге перезагрузил мми раньше времени, скрипт не доработал получается - эта запись есть в логе

Patch Started. Copying Dumper script
Dumper script copyed. Copying application

вот этой записи нет -

Application copied.
DONE.

итог - ММИ не стартует
востанавливать только со снятием - через разьем?
или есть возможность скриптом каким поправить?
С уважением

sergeynik

08.02.2015, 21:53

да через консоль

eprst

08.02.2015, 22:00

да через консоль
понял, спасибо
еще вопрос - прошивка 770 стоит (а6 4G), есть смысл обновлять на свежее?

zerbino

08.02.2015, 22:39

востанавливать только со снятием - через разьем?
или есть возможность скриптом каким поправить?
С уважением
Адаптер не нужен?:rolleyes:

eprst

08.02.2015, 22:50

Адаптер не нужен?:rolleyes:
поясни пожалуйста

eprst

09.02.2015, 16:57

вопрос - прошивка 770 стоит (а6 4G), есть смысл обновлять на свежее? на 782 или 783?

eprst

11.02.2015, 14:49

ввел команды -
mount -uw /mnt/efs-persist/
rm /mnt/efs-persist/MMI3GApplication
вроде ожила

diamax

13.02.2015, 13:37

Ребята ! Помогите ,проблема в железе ?! Вот лог , началось в морозы
IPL: Audi 3G 9308 (SH7785) / QNX 6.3.0 [PL_qnx_ipl-3g_9308-sh7785_08253A, built
2008/06/18_15-16-25_UTC]
CPU: SH7785 (>= 5th cut, clk mode 20. 4xDDR), 792MHz
RAM: 512 MB (probed, DBCONF=e30002)
FLASH: Spansion S29GL512N (32bit): 512 sectors x 256K
FPGA: PL_MMI3G_PLUS_FPGA_9411_D1_11185A (0ms)

Entering CLI, type '?' or 'help' for help

=>
=> help
? - alias for 'help'
bconf - display boot manager configuration
bios - start BIOS
boot - boot image in memory/flash
diag_p1j - diagnostic for the PLL1 clock jitter problem
download - download IFS over serial line (sendnto protocol)
echo - echo args
fpga - load FPGA from image in memory/flash
go - jump to 'addr'
help - print online help
hwconf - dump hardware configuration
md - memory display
memperf - memory performance test (benchmark)
memtest - memory test
mt - alias for 'memtest'
pci - lists pci devices
qinfo - display QNX build information
rsupdate - query read shifter update mode (workaround for SH7785 limitation #48)

rz - alias for 'zmodem'
scan - scan flash for images (FPGA, IFS, BIOS packet)
version - print program version
zmodem - download IFS or FPGA over serial line (Z-Modem protocol)
=> flashit -a 40000 -e 1000
Unknown command 'flashit' - try 'help'
=> fpga
missing/invalid argument/option
=> flashit-a 40000 -e 1000
Unknown command 'flashit-a' - try 'help'
=> help
? - alias for 'help'
bconf - display boot manager configuration
bios - start BIOS
boot - boot image in memory/flash
diag_p1j - diagnostic for the PLL1 clock jitter problem
download - download IFS over serial line (sendnto protocol)
echo - echo args
fpga - load FPGA from image in memory/flash
go - jump to 'addr'
help - print online help
hwconf - dump hardware configuration
md - memory display
memperf - memory performance test (benchmark)
memtest - memory test
mt - alias for 'memtest'
pci - lists pci devices
qinfo - display QNX build information
rsupdate - query read shifter update mode (workaround for SH7785 limitation #48)

rz - alias for 'zmodem'
scan - scan flash for images (FPGA, IFS, BIOS packet)
version - print program version
zmodem - download IFS or FPGA over serial line (Z-Modem protocol)
IPL: Audi 3G 9308 (SH7785) / QNX 6.3.0 [PL_qnx_ipl-3g_9308-sh7785_08253A, built
2008/06/18_15-16-25_UTC]
CPU: SH7785 (>= 5th cut, clk mode 20. 4xDDR), 792MHz
RAM: 512 MB (probed, DBCONF=e30002)
FLASH: Spansion S29GL512N (32bit): 512 sectors x 256K
FPGA: PL_MMI3G_PLUS_FPGA_9411_D1_11185A (0ms)

Entering CLI, type '?' or 'help' for help

=> ~8~
Unknown command '~8~' - try 'help'
=> boot 1c0000
starting image @801c0000 ...

Startup: PL_qnx_startup-sh7785_09332A, built 2009/08/11_11-10-29_UTC
RAM : 128 MB @0x08000000
RAM : 128 MB @0x40000000
RAM : 256 MB @0x50000000
FLASH: 128 MB @0x00000000
FPGA IRQ: Interrupt Controller ID:33 Ver:2.1.0 ILVL:7 Lines:255

System page at phys:0800a000 user:0800a000 kern:8800a000
Starting next program at v88046b20
intrentry_base = 8ffe5630, size=2176
copying intrentry code:
intrentry_code_buf = 88085f28
intrentry_base = 8ffe5630
copy_size = 2432
final intrentry_base = 8ffe5630, size=2176
------------------------------------------------------
Welcome to QNX 6.3.2 (RL_qnx_os_632_PSP3_09423A) MMI3G Audi EMERGENCY SETUP 1021
4A
starting pci driver
*** init FPGA registers ***
[pcidma] PL_qnx_pcidma_FMod08363A_09274A, built 2009/07/02_11-10-37_UTC
starting dev-ipc for IOC
initialize IPC Driver
starting network driver
starting atapi driver - setup device /dev/cam0
[pcidma] finished.
[pcidma] finished.
xpt_configure: No eide interfaces found
Unable to access "/dev/cam0" (2)
starting devc-pty
starting flash driver
starting SDCard driver
Path=0 -
target=0 lun=0 Direct-Access(0) - SU08G Rev: 8.0
Unable to access "/dev/io-net/en5" (2)
starting with no network driver
================================================== =========
Emergency IFS is started. Emergency app tries to restore
the application.
================================================== =========
53264 running /usr/bin/devg-NVTIRM
DMA is Disabled
dma disabled, interrupt thread priority = 100
53266 running /sbin/io-media-nvidia
53267 running /usr/sbin/io-display
53268 running /usr/apps/MMI3GEmergencyApp
================================================== =========
Emergency shell started, fix your system and restart again
================================================== =========
discplayer_init: IN
nvidia_render_manager_init: IN
INvmRenderManager::GetNvmRenderManager (&pRenderManager);
er = pRenderManager->Init(oConfig);
# biosApp FPGA valid 1
Emergency FPGA valid 1
Disabling IOC watchdog

EmergencyApp-MMI3G: version 31.19.2098, date of build 08.09.2009
pRenderManager->Open()
nvidia_render_manager_init: OUT
discplayer_init: OUT
discplayer_init
discplayer_init: IN
nvidia_render_manager_init: IN
nvidia_render_manager_init: OUT
discplayer_init: OUT
dvdtrackplayer_init
discplayer_init: IN
nvidia_render_manager_init: IN
nvidia_render_manager_init: OUT
discplayer_init: OUT
dvdnavigator_init
created navigator control point with 8249288
mixer_init: IN
mixer_init: OUT
NvTRACELEVEL set to 3 (Level Info)
nVAudio_init: IN
nvidia_render_manager_init();
nvidia_render_manager_init: IN
nvidia_render_manager_init: OUT
nVAudio_init: OUT
installing audio decoders
installing video decoders
nVAudio_init: IN
nvidia_render_manager_init();
nvidia_render_manager_init: IN
nvidia_render_manager_init: OUT
nVAudio_init: OUT
OnIpcGetCaptureUnitSourceCount
Number of displays: 6
Number of layers: 9
Graphics init was successfull: DisplaySize is 800x 480
The FPGA for the application is valid!
Emergency application will do nothing!
result of running command start_efs_driver.sh is 0
HBpersistence is available!
************************************************** *********
** DeveloperMode is off!!!! **
** The system will shutdown soon! **
** DO NOT FLASH WITH SCRIPTS IN THIS MODE!!! **
************************************************** *********
** You can enable DeveloperMode like this: **
** echo dummy > /HBpersistence/DeveloperMode **
************************************************** *********
Set DisplayStatus to 2
Set DisplayStatus to 4
OnOff: process IPC event HWsample 209 HWvariant 178 FinalShutdown 0
OnOff: process IPC event HWsample 209 HWvariant 178 FinalShutdown 0
OnOff: process IPC event HWsample 209 HWvariant 178 FinalShutdown 0
OnOff: process IPC event HWsample 209 HWvariant 178 FinalShutdown 0
Set DisplayStatus to 6
OnOff: process IPC event HWsample 209 HWvariant 178 FinalShutdown 0
OnOff: process IPC event HWsample 209 HWvariant 178 FinalShutdown 0
OnOff: process IPC event HWsample 209 HWvariant 178 FinalShutdown 0
OnOff: process IPC event HWsample 209 HWvariant 178 FinalShutdown 0
OnOff: process IPC event HWsample 209 HWvariant 178 FinalShutdown 0
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
OnOff: process IPC event HWsample 209 HWvariant 178 FinalShutdown 0
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
OnOff: process IPC event HWsample 209 HWvariant 178 FinalShutdown 0
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
OnOff: process IPC event HWsample 209 HWvariant 178 FinalShutdown 0
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
f3s_a29f040_v2sync: 84 DQ5 error
(devf t2::f3s_unit_refresh:656) fs1p3 error 5
f3s_a29f040_v2sync: 84 DQ5 error
(devf t2::f3s_unit_refresh:656) fs1p3 error 5
f3s_a29f040_v2sync: 84 DQ5 error
(devf t2::f3s_unit_refresh:656) fs1p3 error 5
при прошивке тоже самое
OnOff: Progress 094
OnOff: Progress 095
OnOff: Progress 097
OnOff: Progress 098
OnOff: Progress 100
SWDL: Stopping EFS driver!
result of running command stop_efs_driver.sh is 0
SWDL: Starting EFS driver (automount)!
result of running command start_efs_driver.sh is 0
/HBpersistence/SWDL is available!
f3s_a29f040_v2sync: 84 DQ5 error
(devf t2::f3s_unit_refresh:656) fs0p3 error 5
f3s_a29f040_v2sync: 84 DQ5 error
(devf t2::f3s_unit_refresh:656) fs0p3 error 5
f3s_a29f040_v2sync: 84 DQ5 error
(devf t2::f3s_unit_refresh:656) fs0p3 error 5
f3s_a29f040_v2sync: 84 DQ5 error
(devf t2::f3s_unit_refresh:656) fs0p3 error 5

АлександрКиров

18.02.2015, 15:45

ввел команды -
mount -uw /mnt/efs-persist/
rm /mnt/efs-persist/MMI3GApplication
вроде ожила

Где и как ввел? Можно подробней.У меня та же история.

Vlasoff

19.02.2015, 02:30

jalib

19.02.2015, 06:04

Кракозябры скорее всего из-за неправильной скорости порта. Нужно
115200,8,1, parity none, flow control XON/XOFF

АлександрКиров

19.02.2015, 07:18

Кракозябры скорее всего из-за неправильной скорости порта. Нужно
115200,8,1, parity none, flow control XON/XOFF
Привет всем.А у меня совсем ни чего не открывается после " не дождался окончания работы скрипта,"Подскажите что сейчас делать.?

Vlasoff

19.02.2015, 08:38

Кракозябры скорее всего из-за неправильной скорости порта. Нужно
115200,8,1, parity none, flow control XON/XOFF
Jabib, пробовал скорость разную, и эту тоже.
Какие симптомы будут если кабель неправильный?

jalib

19.02.2015, 08:48

Скорее ничего не будет. Лично я не стал морочиться с паянием, плясками последовательным портом и т.д. и взял адаптер на usb, у ребят тут на форуме.

Vlasoff

19.02.2015, 09:04

Скорее ничего не будет. Лично я не стал морочиться с паянием, плясками последовательным портом и т.д. и взял адаптер на usb, у ребят тут на форуме.
Ясно. А драйвер какой ставили?

АлександрКиров

20.02.2015, 10:57

Vlasoff

21.02.2015, 01:10

Сергейник, а также интернет сообщество, взываю о помощи!
Такая же ситуация как в посте №299 от eprst. не дождался окончания работы скрипта, ребутнул, апликейшн не докопировался.
Подключился по схеме, но вижу кракозябры! Как ее научить нормально мне отвечать через последовательный интерфейс?? Чтобы можно было читать лог и посылать команды. потому что вижу что грузится и что то выдает, в IPL один набор знаков, в обычном буте другой набор символов, но непонятно на каком языке.. не пойму, то ли с кодировкой проблемы то ли еще с чем.. перебробовал три разных компа, и с железным ком портом и с ком-юсб.. скорости порта, настройки кодировки.. команды могу вводить но вводится тоже сплошная хрень.. одно и тоже. Скрины во вложении.
Хелп, друзья!

Решил проблему сам, здесь помощи не дождался.
Проблему с кракозябрами решил сменой шнурка. Заказал плату UART на чипе FTDI, распаял выходы и все заработало. Теперь у меня есть правильный кабель.
Ввел команды
mount -uw /mnt/efs-persist/
rm /mnt/efs-persist/MMI3GApplication
перезагрузил, голова подумала пару минут и ожила. Перепрошил из Emergency mode с нуля, поставил карты, все гуд.
В Москве могу оказать помощь, если вы уложили свою голову, денег не возьму, принимаются ништяки или пиво ну и человеческое спасибо:)

АлександрКиров

21.02.2015, 08:11

Решил проблему сам, здесь помощи не дождался.
Проблему с кракозябрами решил сменой шнурка. Заказал плату UART на чипе FTDI, распаял выходы и все заработало. Теперь у меня есть правильный кабель.
Ввел команды
mount -uw /mnt/efs-persist/
rm /mnt/efs-persist/MMI3GApplication
перезагрузил, голова подумала пару минут и ожила. Перепрошил из Emergency mode с нуля, поставил карты, все гуд.
В Москве могу оказать помощь, если вы уложили свою голову, денег не возьму, принимаются ништяки или пиво ну и человеческое спасибо:)
Молодец.Жаль что я не в Москве живу,иначе обязательно бы подъехал.

S4Mike

22.02.2015, 18:44

The image file "efs-persist.bin" is not available via the Firmware Update files.
You have to extract it, from another, fully functional main unit with the following command:

"cat /dev/fs0p3 > /fs/sd0/backup/flashdump/fs0p3_efs-persist.bin" for the 1st SD Slot of the Unit.

Now you have the flashdump image of the efs-persist partition (fs0p3), to flash it on the broken unit as descriped above...

I have a corrupt efs-persist partition (MMI model 9308). I do not have access to another MMI unit. Can someone please post efs-persist.bin? I have searched and I cannot find it. I apologize for the poor Russian - using Google translate.

У меня естькоррумпированные системы EFS сохраняются раздел ( MMI модели 9308 ). Я не имею доступ к другому MMI устройства. Может кто-то пожалуйста, напишите EFS - persist.bin ? Я искал , и я не могу ее найти. Я прошу прощения заплохой русский - с помощью Google Translate.

Tschako

02.03.2015, 00:33

Also you CAN Find an efs-persist image on a K0257 Firmware SD-Card:
8R0 906 961 DF (HIGH_EU_K0257)
Path: "\ 3 \ MU9308 \ efs-persist \ 41 \ Default \ efs-persist.efs"
Try it and Give Feedback!

walawa75

07.03.2015, 01:36

Hello Tschako and thank you for the great work you are doing.

Is there anyway to dump an efs-persist.bin from SD slot with a SD script ? Or needed to unmount the MMI ? Thanks for the reply.

Tschako

07.03.2015, 21:03

See post # 318
efs-persist.efs and efs-persist.bin are the same binary image files.

abacus

10.03.2015, 14:03

Ребята, кто сможет помочь с такой проблемкой. Постараюсь описать: блок MMI 3g 4E0 035 670F, работает всё кроме навигации (спутники -0), требует калибровки (вставлю фотку). Рассчитываю на подсказку или помощь. У меня стоит такой же блок только ...666 работает всё абсолютно (но звук какой-то дебёлый). Вот только из-за звука и хочу его поставить.
34795

Rzannikov

02.04.2015, 14:12

Ден добрый. Больше года назад накрылась MMI 3G hight (8T1 035 670 D). На тот момент единственное решение было замена. На eBay заказал б/у. Официал активировал. Все ок!
Решил поднять старую голову. Уж больно она не дешево стоит. Да и на коробке печатная плата накрылась, а ремонт не дешевый.
Так вот, что хотел спросит:
1. Как я понимаю голову необходимо подключить к авто. На данный момент там стоит новая и прописанная. Грозит ли чем нибудь перестановка головы?
2. Живу я в городе маленьком и единственный ft232 в моем vag-com. Думаю шить на CP210x. Data кабеля от Nokia вроде на этом чипе и напряжение там 3.3v изначально. Прошу совета по это варианту. Подойдет?

knfevg

04.04.2015, 22:47

В процессе подключения RPI для получение Ауди Онлайн, после того как все уже заработало, я решил вписать пару строк для автозапуска при включение ММИ. Добавил я их в startDumper.sh и как видно сделал что-то не правильно.
Изначально startDumper.sh был
#!/bin/fesh
/usr/sbin/dumper -m -w -z 1 -c -d /HBpersistence/core -d /mnt/persistence -f io-pkt-v4-hc -f devc-serusb -f io-usb

Я сделал:
#!/bin/fesh
/usr/sbin/dumper -m -w -z 1 -c -d /HBpersistence/core -d /mnt/persistence -f io-pkt-v4-hc -f devc-serusb -f io-usb
setconf _CS_RESOLVE "nameserver_8.8.8.8"
route add default 192.168.1.254

Записал, перезагрузил и теперь ММИ "мертвый" (не включается, кнопки не горят, на vagcom не реагирует..). Единственный вариант это терминал? Скриптом его не починить? Машина гарантийная. Есть смысл идти к официалам?

Rzannikov

06.04.2015, 15:50

Можно попробовать на дурака. Типа сел в тачку, а MMI не фурычит.
Главное что бы не было видно слетов твоего присутствия.
Еще где то натыкался на доки по замене вышедших из строя MMI, но ща уже не помню. Тут надо ковать http://www.club-q5.ru/forum/

Rzannikov

07.04.2015, 19:16

Подключился. Но дальнейшие действия предпринимать не стал, опасаясь навредить.
Подскажите, что далее?

Rzannikov

09.04.2015, 13:36

Команда boot 1c0000 дает такой результат

knfevg

09.04.2015, 13:44

УРА!!! Сегодня весь блок поменяли по гарантии!!!!!

Crash-100

10.04.2015, 08:58

MMI 3G не работает внутренний Bluethooth - все настройки в зеленке включены, в 17 канале 1 стоит, что может быть, прошивка K257, может кто боролся с данной проблемой.

abacus

10.04.2015, 15:07

MMI 3G не работает внутренний Bluethooth - все настройки в зеленке включены, в 17 канале 1 стоит, что может быть, прошивка K257, может кто боролся с данной проблемой.
посмотри и почитай здесь:
http://www.audi-club.ru/forum/showpost.php?p=5991968&postcount=1598

Crash-100

10.04.2015, 15:44

ну как написал выше все это сделано

abacus

10.04.2015, 15:54

ну как написал выше все это сделано
Какой у тебя блок стоит? 4E0035646 или что-то другое?

Crash-100

10.04.2015, 15:59

4e0035666

abacus

10.04.2015, 16:15

4e0035666

А попробуй фиксовский диск по моему вот этот если не ошибаюсь 8R0 906 961 L. У меня была проблема такая же, только на блоке 4e0035646. Все везде прописано, 1 стоит - блютуса нет и хоть ты тресни. Этот диск как раз и правит блютуз.

abacus

10.04.2015, 16:20

А попробуй фиксовский диск по моему вот этот если не ошибаюсь 8R0 906 961 L. У меня была проблема такая же, только на блоке 4e0035646. Все везде прописано, 1 стоит - блютуса нет и хоть ты тресни. Этот диск как раз и правит блютуз.
Скачал сейчас disk L, по-моему он тебе не идёт...

Vlasoff

23.04.2015, 01:16

Други, помогите. читаю епром блока 5f vcp, доходит до адреса 00200 и дальше eeprom reading error.. что делать как прочитать?

Hoto

17.06.2015, 20:59

Доброго времени.
Вопрос - Где можно найти прошивку для MU9309 ( или откуда она взялась в системе?)?
И как убрать FPDA EmApp 31.19.2098 ?
Не даёт залить родную прошивку.(MU9307):sorrow:

Crash-100

18.06.2015, 21:46

Из того, что ты написал я ничего не понял!

kibsoft

18.06.2015, 22:35

Здравствуйте всем,
кто сталкивался,подскажите, плиз - при обновлении ПО головы вылезла ошибка чтения файла (3 диска прошились нормально,на 4ом ошибка вылезла),соотвественно процесс прервался,получился зеленый экран.при включении пытается шиться дальше, но в процессе выходит ошибка file error.появляется именно во время erase операции, но каждый раз на разной стадии. что это - сдохший лазер привода или флеш сама,куда шьется прошивка? или? проверено разными дисками, результат тот же. 3774037741

Hoto

21.06.2015, 20:44

Поясню.
Q7 12 года. На юните написано MU9307 FW 022/
Прошили прошивкой 0776, всё было хорошо пока не обновили карты, возникли проблемы с активацией. Пробовали откатить, получили кирпич.
В терминале провели флашит, запустилось эмердженси , но тот просит MU9309 обновление (я такое не нашел) .
Хотелось бы понять как установить родное MU9307.

Hoto

06.07.2015, 18:37

Что можно с этой проблемой сделать?

dikij

07.07.2015, 22:16

Доброго времени.

Ребята, кто сможет помочь с такой проблемкой Audi a6 4g mmi mit hdd

dikij

09.07.2015, 20:27

Доброго времени.
Ребята вот токая ерунда вышла во время активации с (K0770_Activator_MMI_3GP_thx_to_Carson) был cбой и я сделал резет MMI после чего MMI умер экран не открывает резет не чего недаёт хотя слышно что перезагружает помогите оживить пожалуйста через 5 дней в отпуск а MMI здох.
Audi a6 4g
MMI c hdd
Soft 770
Navi 8R0060884CH

Crash-100

09.07.2015, 20:51

Присылай !

zerbino

09.07.2015, 21:20

dikij

10.07.2015, 07:37

я в германии

a4ss4abt

13.07.2015, 01:13

Hi guys, i'm here again because I have an Audi 3G 9308 unit with a strange new problem, the unit is quite working for sometimes but after few minutes it begins to re-boot by itself, and if I connect by serial port it Begins A loop like the following One and I CAN not control it:

"IPL: Audi 3G 9308 (SH7785) / QNX 6.3.0 [PL_qnx_ipl-3g_9308-sh7785_07412A, built 2007/10 / 09_12-19-44_UTC]
CPU: SH7785 ( > = 5th cut, clk mode 20), 792MHz
RAM: 512 MB (probed, DBCONF = e30002)
FLASH: Spansion S29GL512N: Sectors 512 x 256K
FPGA: PL_MMI3G_FPGA_9308_D1_08492A
(0ms)
*** Old-fashioned Mark found on IFS @ 0x1c0000: .zero = 0x3000001d
*** Old-fashioned Mark found on IFS @ 0x780000: .zero = 0x10000000
starting image @ 780000 ...

closep
=== UNEXPECTED EXCEPTION # 180 !!!

- PC = 8801b53e
- PR = 8801479c
- SR = 400000f1
- R0 = 400000f0 R1 = 8801cc50 R2 = e500e498 R3 = ffeb0010
- R4 = 88013960 R5 = 780000 R6 = 100 R7 = 80009e30
- R8 = 4 R9 = 8801b540 R10 = c R11 = 8801cf00
- R12 = ffff R13 = 40000 R14 = e5011e2c R15 = 8801cc08
=============================================== =================

IPL: Audi 3G 9308 (SH7785) / QNX 6.3.0 [PL_qnx_ipl-3g_9308-sh7785_07412A, built 2007/10 / 09_12-19-44_UTC]
CPU: SH7785 (> = 5th cut, clk mode 20), 792MHz
RAM: 512 MB (probed, DBCONF = e30002)
FLASH: Spansion S29GL512N: Sectors 512 x 256K
FPGA: PL_MMI3G_FPGA_9308_D1_08492A (0ms)
*** Old-fashioned Mark found on IFS @ 0x1c0000: .zero = 0x3000001d
*** Old-fashioned Mark found on IFS @ 0x780000: .zero = 0x10000000
starting @ 780000 image ... "

closep
=== UNEXPECTED EXCEPTION # 180 !!!"

Please Look at the log joint here

many many thanks for your help

Hoto

18.07.2015, 14:49

Было до удаления

boot 1c0000
starting image @801c0000 ...

Startup: PL_qnx_startup-sh7785_09332A, built 2009/08/11_11-10-29_UTC

RAM : 128 MB @0x08000000
RAM : 128 MB @0x40000000
RAM : 256 MB @0x50000000
FLASH: 128 MB @0x00000000
FPGA IRQ: Interrupt Controller ID:33 Ver:2.1.0 ILVL:7 Lines:255

System page at phys:0800a000 user:0800a000 kern:8800a000
Starting next program at v88046b20
intrentry_base = 8ffe5630, size=2176
copying intrentry code:
intrentry_code_buf = 88085f28
intrentry_base = 8ffe5630
copy_size = 2432
final intrentry_base = 8ffe5630, size=2176
------------------------------------------------------
Welcome to QNX 6.3.2 (RL_qnx_os_632_PSP3_09423A) MMI3G Audi EMERGENCY SETUP 10214A
starting pci driver
*** init FPGA registers ***
[pcidma] PL_qnx_pcidma_FMod08363A_09274A, built 2009/07/02_11-10-37_UTC
starting dev-ipc for IOC
initialize IPC Driver
starting network driver
starting atapi driver - setup device /dev/cam0
starting devc-pty
starting flash driver
Path=0 - XILINX ATAPI
target=0 lun=0 CD-ROM(5) - FJ-TEN DVD-ROM DV-05FT2 Rev: 1B20
Path=1 - XILINX ATAPI
target=1 lun=0 Direct-Access(0) - TOSHIBA MK6050GA Rev: TJ10
starting SDCard driver
Path=0 -
target=0 lun=0 Direct-Access(0) - SD02G Rev: 8.0
Unable to access "/dev/io-net/en5" (2)
starting with no network driver
================================================== =========
Emergency IFS is started. Emergency app tries to restore
the application.
================================================== =========
49169 running /usr/bin/devg-NVTIRM
DMA is Disabled
dma disabled, interrupt thread priority = 100
49171 running /sbin/io-media-nvidia
49172 running /usr/sbin/io-display
49173 running /usr/apps/MMI3GEmergencyApp
================================================== =========
Emergency shell started, fix your system and restart again
================================================== =========
discplayer_init: IN
nvidia_render_manager_init: IN
INvmRenderManager::GetNvmRenderManager (&pRenderManager);
er = pRenderManager->Init(oConfig);
# Fpga header is not 0x4744482e (0xffffffff)!
App FPGA valid 0
Emergency FPGA valid 1
Disabling IOC watchdog

EmergencyApp-MMI3G: version 31.19.2098, date of build 08.09.2009
pRenderManager->Open()
nvidia_render_manager_init: OUT
discplayer_init: OUT
discplayer_init
discplayer_init: IN
nvidia_render_manager_init: IN
nvidia_render_manager_init: OUT
discplayer_init: OUT
dvdtrackplayer_init
discplayer_init: IN
nvidia_render_manager_init: IN
nvidia_render_manager_init: OUT
discplayer_init: OUT
dvdnavigator_init
created navigator control point with 8249288
mixer_init: IN
mixer_init: OUT
NvTRACELEVEL set to 3 (Level Info)
nVAudio_init: IN
nvidia_render_manager_init();
nvidia_render_manager_init: IN
nvidia_render_manager_init: OUT
nVAudio_init: OUT
installing audio decoders
installing video decoders
nVAudio_init: IN
nvidia_render_manager_init();
nvidia_render_manager_init: IN
nvidia_render_manager_init: OUT
nVAudio_init: OUT
OnIpcGetCaptureUnitSourceCount
Number of displays: 6
Number of layers: 9
Graphics init was successfull: DisplaySize is 800x 480
Set DisplayStatus to 2
OnOff: process IPC event HWsample 177 HWvariant 9 FinalShutdown 0
SWDL: startUpdate HW index 177, variant 9309
OnOff: phase Scan metainfo
We have to erase the FPGA, init the FPGA persistence and delete the orphaned headers (if there are any).
OnOff: phase Erase
OnOff: Progress 000
dev_fd == 11
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0x40000
limit: 0x40000
Set DisplayStatus to 4
devctl(11,-2146694912,xx,12,0) returned 0OnOff: Progress 100
CEmergencySwdlDevCtrl::continueAfterEraseFpgaIniti al
SWDL: Stopping EFS driver!
result of running command stop_efs_driver.sh is 0
SWDL: Starting EFS driver (automount)!
result of running command start_efs_driver.sh is 0
(devf t1::f3s_table_find:247) fs0p3 corrupt U: 74
Set DisplayStatus to 6
/HBpersistence/SWDL not found!
/HBpersistence/SWDL not found!
/HBpersistence/SWDL not found!
/HBpersistence/SWDL not found!
/HBpersistence/SWDL not found!
/HBpersistence/SWDL not found!
/HBpersistence/SWDL not found!
/HBpersistence/SWDL not found!
/HBpersistence/SWDL not found!
/HBpersistence/SWDL not found!
SWDL persistence is not available!
useDefaultValuesForInfo: MU
FPGA info header @SWDL V1@
FPGA info version 1
FPGA info variant 9309
FPGA info type Main Unit
FPGA info HW index 21
FPGA info region <noRegion>
FPGA info step 0
FPGA info HW index IT 0
FPGA info ignore region/variant 1
FPGA info loop 0
FPGA info repeat 0
FPGA info CRC 5e17bb56
SWDL: Stopping EFS driver!
result of running command stop_efs_driver.sh is 0
SWDL: Starting EFS driver (automount)!
result of running command start_efs_driver.sh is 0
(devf t1::f3s_table_find:247) fs0p3 corrupt U: 74
/HBpersistence/SWDL not found!
/HBpersistence/SWDL not found!
/HBpersistence/SWDL not found!
/HBpersistence/SWDL not found!
/HBpersistence/SWDL not found!
/HBpersistence/SWDL not found!
/HBpersistence/SWDL not found!
/HBpersistence/SWDL not found!
/HBpersistence/SWDL not found!
/HBpersistence/SWDL not found!
/HBpersistence/SWDL/update.txt doesn't exist
Don't use update.txt
SWDL: Mount from medium 3 (0)
OnOff: variant 9309
OnOff: DeviceName MU9309
Src: Medialauncher is running
Src: mount failed. Retry once in 1 s
Src: Medialauncher is running
Src: mount failed (medium unavailable 2)
SWDL: mount failed
SWDL: Mount from medium 4 (1)
Src: Medialauncher is running
Src: mount OK
SWDL: mount OK
SWDL: open metainfo /metainfo2.txt
SWDL: open finished (9389)
OnOff: FileAccess for continues!
OnOff: Current file access type: read
SWDL: read finished (9389, 0)
SWDL: parse metainfo
SWDL: check next subdir
SWDL: CheckNextSubDir 1
SWDL: open metainfo /metainfo2.txt
SWDL: open finished (19921)
SWDL: read finished (19921, 0)
SWDL: parse metainfo
SWDL: check next subdir
SWDL: CheckNextSubDir 2
SWDL: open metainfo /metainfo2.txt
SWDL: open finished (22490)
SWDL: read finished (22490, 0)
SWDL: parse metainfo
SWDL: check next subdir
SWDL: CheckNextSubDir 3
SWDL: open metainfo /metainfo2.txt
SWDL: open finished (92291)
SWDL: read finished (92291, 0)
SWDL: parse metainfo
SWDL: check next subdir
SWDL: CheckNextSubDir 4
SWDL: Mount from medium 5 (2)
Src: Medialauncher is running
Src: mount failed. Retry once in 1 s
Src: Medialauncher is running
Src: mount failed (medium unavailable 2)
SWDL: mount failed
SWDL: Mount from medium 2 (3)
Src: mount from CD ... still waiting...
Src: mount from CD ... still waiting...
Src: mount from CD ... still waiting...
Src: mount from CD ... still waiting...
Src: mount from CD ... still waiting...
Src: mount from CD ... still waiting...
Src: mount from CD ... still waiting...
Src: mount from CD ... still waiting...
Src: mount from CD ... still waiting...
Src: mount from CD ... still waiting...
Src: mount from CD ... still waiting...
Src: mount from CD ... still waiting...
Src: mount from CD ... still waiting...
Src: mount from CD ... still waiting...
Src: mount from CD ... still waiting...
Src: mount from CD ... still waiting...
Src: mount from CD ... still waiting...
Src: mount from CD ... still waiting...
Src: mount from CD ... still waiting...
Src: mount from CD failed - we give up
Src: mount failed (medium unavailable 2)
SWDL: mount failed
SWDL: No medium left!
OnOff: error No medium!!!
result of running command start_efs_driver.sh is 0
(devf t1::f3s_table_find:247) fs1p3 corrupt U: 74
Wait for HBpersistence...
Wait for HBpersistence...
Wait for HBpersistence...
Wait for HBpersistence...
Wait for HBpersistence...
Wait for HBpersistence...
Wait for HBpersistence...
Wait for HBpersistence...
Wait for HBpersistence...
Wait for HBpersistence...
HBpersistence is not available!
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
booEnabling IOC watchdog
t Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
bEnabling IOC watchdog
ootEnabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Initiate shutdown (after BEM timeout)...

Hoto

18.07.2015, 14:50

Стало

[SERIAL/MODEM] CONNECTED TO PORT com18 (115200-8N1)

ю
getdip
close
IPL: Audi 3G 9308 (SH7785) / QNX 6.3.0 [PL_qnx_ipl-3g_9308-sh7785_08253A, built 2008/06/18_15-16-25_UTC]
CPU: SH7785 (>= 5th cut, clk mode 20. 4xDDR), 792MHz
RAM: 512 MB (probed, DBCONF=e30002)
FLASH: Spansion S29GL512N (32bit): 512 sectors x 256K
*** NO FPGA loaded!

Hoto

18.07.2015, 14:50

затем

=> boot 1c0000
starting image @801c0000 ...

Startup: PL_qnx_startup-sh7785_09332A, built 2009/08/11_11-10-29_UTC

RAM : 128 MB @0x08000000
RAM : 128 MB @0x40000000
RAM : 256 MB @0x50000000
FLASH: 128 MB @0x00000000
FPGA IRQ: Interrupt Controller ID:32 Ver:32.32.32
FPGA IRQ: ERROR: Interrupt Controller not supported!
** STOP **
¦
getdip
close
IPL: Audi 3G 9308 (SH7785) / QNX 6.3.0 [PL_qnx_ipl-3g_9308-sh7785_08253A, built 2008/06/18_15-16-25_UTC]
CPU: SH7785 (>= 5th cut, clk mode 20. 4xDDR), 792MHz
RAM: 512 MB (probed, DBCONF=e30002)
FLASH: Spansion S29GL512N (32bit): 512 sectors x 256K
*** NO FPGA loaded!

Entering CLI, type '?' or 'help' for help

=> ?
? - alias for 'help'
bconf - display boot manager configuration
bios - start BIOS
boot - boot image in memory/flash
diag_p1j - diagnostic for the PLL1 clock jitter problem
download - download IFS over serial line (sendnto protocol)
echo - echo args
fpga - load FPGA from image in memory/flash
go - jump to 'addr'
help - print online help
hwconf - dump hardware configuration
md - memory display
memperf - memory performance test (benchmark)
memtest - memory test
mt - alias for 'memtest'
pci - lists pci devices
qinfo - display QNX build information
rsupdate - query read shifter update mode (workaround for SH7785 limitation #48)
rz - alias for 'zmodem'
scan - scan flash for images (FPGA, IFS, BIOS packet)
version - print program version
zmodem - download IFS or FPGA over serial line (Z-Modem protocol)
=> zmodem
zmodem_rx: establishing contact with sender

Upload Zmodem
SystemFPGA.hbbin (729.0 KB, 1:08 min = 10.7 KB/sec)

--- zmodem done: err=0, imaddr=0x8c000000
FPGA: PL_MMI3G_FPGA_9308_D1_09324A

(0ms)
=> fpga 100000
*** could not load FPGA image @80100000: invalid format (no .HDG or .HDE tag)
missing/invalid argument/option
=> boot fpga
missing/invalid argument/option
=> boot 1c0000
starting image @801c0000 ...

Startup: PL_qnx_startup-sh7785_09332A, built 2009/08/11_11-10-29_UTC

RAM : 128 MB @0x08000000
RAM : 128 MB @0x40000000
RAM : 256 MB @0x50000000
FLASH: 128 MB @0x00000000
FPGA IRQ: InterruptLevelMask Register

System page at phys:0800a000 user:0800a000 kern:8800a000
Starting next program at v88046b20
intrentry_base = 8ffef038, size=2220
copying intrentry code:
intrentry_code_buf = 88085f28
intrentry_base = 8ffef038
copy_size = 2476
final intrentry_base = 8ffef038, size=2220
------------------------------------------------------
Welcome to QNX 6.3.2 (RL_qnx_os_632_PSP3_09423A) MMI3G Audi EMERGENCY SETUP 10214A
starting pci driver
*** init FPGA registers ***
Unable to access "/dev/sysregs" (2)
starting dev-ipc for IOC
initialize IPC Driver
Can't start driver '/dev/ipc/onoff'starting network driver
starting atapi driver - setup device /dev/cam0
InterruptAttachEvent failed
InterruptAttachEvent failed
xpt_configure: No eide interfaces found
Unable to access "/dev/cam0" (2)
starting devc-pty
starting flash driver
starting SDCard driver
Unable to access "/dev/io-net/en5" (2)
starting with no network driver
================================================== =========
Emergency IFS is started. Emergency app tries to restore
the application.
================================================== =========
69644 running /usr/bin/devg-NVTIRM
DMA is Disabled
dma disabled, interrupt thread priority = 100
69646 running /sbin/io-media-nvidia
69647 running /usr/sbin/io-display
69648 running /usr/apps/MMI3GEmergencyApp
================================================== =========
Emergency shell started, fix your system and restart again
================================================== =========
discplayer_init: IN
nvidia_render_manager_init: IN
INvmRenderManager::GetNvmRenderManager (&pRenderManager);
er = pRenderManager->Init(oConfig);
# Fpga header is not 0x4744482e (0xffffffff)!
App FPGA valid 0
Fpga header is not 0x4744482e (0xffffffff)!
Emergency FPGA valid 0
Disabling IOC watchdog
Fpga header is not 0x4744482e (0xffffffff)!

EmergencyApp-MMI3G: version 31.19.0, date of build 08.09.2009
pRenderManager->Open()
nvidia_render_manager_init: OUT
discplayer_init: OUT
discplayer_init
discplayer_init: IN
nvidia_render_manager_init: IN
nvidia_render_manager_init: OUT
discplayer_init: OUT
dvdtrackplayer_init
discplayer_init: IN
nvidia_render_manager_init: IN
nvidia_render_manager_init: OUT
discplayer_init: OUT
dvdnavigator_init
created navigator control point with 8249288
mixer_init: IN
mixer_init: OUT
NvTRACELEVEL set to 3 (Level Info)
nVAudio_init: IN
nvidia_render_manager_init();
nvidia_render_manager_init: IN
nvidia_render_manager_init: OUT
nVAudio_init: OUT
installing audio decoders
installing video decoders
nVAudio_init: IN
nvidia_render_manager_init();
nvidia_render_manager_init: IN
nvidia_render_manager_init: OUT
nVAudio_init: OUT
OnIpcGetCaptureUnitSourceCount
Number of displays: 6
Number of layers: 9

Tschako

18.07.2015, 17:06

Hi Hoto,
think your problem is, that the zmodem upload allways stored at adress 0x8c000000.
You need to prepare an image fitting this star adress from an existing Flash-backup. extract the needed binaeries from 0x8c000000 and flashit.

The emg-ifs normally runs without an working fpga. So you can flashit all you need after a boot from 1c0000 with the flashit tool.

Please, tell us, how you do the zmodem upload? What terminal and what settings, please?

CU
Tschako

Tschako

18.07.2015, 17:11

Try to boot up in IPL and do "scan" command. Then start with boot 1c0000 inot the emg app and erase fpga at 40000.

then make a complete emg-update with the last FW in the SD slot. The unit should download all needed files and restarts fine... then make a normal FW update with the same version to fix all irregulars...

Should work...

Hi guys, i'm here again because I have an Audi 3G 9308 unit with a strange new problem, the unit is quite working for sometimes but after few minutes it begins to re-boot by itself, and if I connect by serial port it Begins A loop like the following One and I CAN not control it:

"IPL: Audi 3G 9308 (SH7785) / QNX 6.3.0 [PL_qnx_ipl-3g_9308-sh7785_07412A, built 2007/10 / 09_12-19-44_UTC]
CPU: SH7785 ( > = 5th cut, clk mode 20), 792MHz
RAM: 512 MB (probed, DBCONF = e30002)
FLASH: Spansion S29GL512N: Sectors 512 x 256K
FPGA: PL_MMI3G_FPGA_9308_D1_08492A
(0ms)
*** Old-fashioned Mark found on IFS @ 0x1c0000: .zero = 0x3000001d
*** Old-fashioned Mark found on IFS @ 0x780000: .zero = 0x10000000
starting image @ 780000 ...

closep
=== UNEXPECTED EXCEPTION # 180 !!!

- PC = 8801b53e
- PR = 8801479c
- SR = 400000f1
- R0 = 400000f0 R1 = 8801cc50 R2 = e500e498 R3 = ffeb0010
- R4 = 88013960 R5 = 780000 R6 = 100 R7 = 80009e30
- R8 = 4 R9 = 8801b540 R10 = c R11 = 8801cf00
- R12 = ffff R13 = 40000 R14 = e5011e2c R15 = 8801cc08
=============================================== =================

IPL: Audi 3G 9308 (SH7785) / QNX 6.3.0 [PL_qnx_ipl-3g_9308-sh7785_07412A, built 2007/10 / 09_12-19-44_UTC]
CPU: SH7785 (> = 5th cut, clk mode 20), 792MHz
RAM: 512 MB (probed, DBCONF = e30002)
FLASH: Spansion S29GL512N: Sectors 512 x 256K
FPGA: PL_MMI3G_FPGA_9308_D1_08492A (0ms)
*** Old-fashioned Mark found on IFS @ 0x1c0000: .zero = 0x3000001d
*** Old-fashioned Mark found on IFS @ 0x780000: .zero = 0x10000000
starting @ 780000 image ... "

closep
=== UNEXPECTED EXCEPTION # 180 !!!"

Please Look at the log joint here

many many thanks for your help

a4ss4abt

18.07.2015, 18:22

Thanks Tschako, I will try the IPL but as I give the boot1c0000 normally it goes in loop with the error message....

Crash-100

18.07.2015, 20:24

- PC = 8801b53e
- PR = 8801479c
- SR = 400000f1
- R0 = 400000f0 R1 = 8801cc50 R2 = e500e498 R3 = ffeb0010
- R4 = 88013960 R5 = 780000 R6 = 100 R7 = 80009e30
- R8 = 4 R9 = 8801b540 R10 = c R11 = 8801cf00
- R12 = ffff R13 = 40000 R14 = e5011e2c R15 = 8801cc08

Мне не очень нравится вот это, сделай тест памяти.

a4ss4abt

18.07.2015, 22:22

Many thanks CRASH-100, I will do it.

Большое спасибо краш-100, я сделаю это.

Hoto

19.07.2015, 19:49

ThanksTschako, try to understand and to perform.

Downloadusing Putty,TeraTerm, 7 ZOC.
\Speed:115200
Databits: 8
\ Stop bits: 1
\Parity: none
\Flow control: XON/XOFF
Where to get the imag efitting this sta radres sfrom anexisting Flash backup?
how do extract the needed binaeries from 0x8c000000 and flashit?
(както так)

a4ss4abt

20.07.2015, 22:19

@Tschako
I did as you suggested but impossible to boot 1c0000 please look:

IPL: Audi 3G 9308 (SH7785) / QNX 6.3.0 [PL_qnx_ipl-3g_9308-sh7785_07412A, built 2007/10/09_12-19-44_UTC]
CPU: SH7785 (>= 5th cut, clk mode 20), 792MHz
RAM: 512 MB (probed, DBCONF=e30002)
FLASH: Spansion S29GL512N: 512 sectors x 256K
FPGA: PL_MMI3G_FPGA_9308_D1_08492A
(0ms)

Entering CLI, type '?' or 'help' for help

=> scan
** @0x80040000: FPGA

total size: 746472 [0x0b63e8]
data: 746212 [0x0b62e4]

.FDR = PL_MMI3G_FPGA_9308_D1_08492A

.FDU = Userinfos zu FPGA 9308_D1_4010_10fv

** @0x80100000: FPGA

total size: 746472 [0x0b63e8]
data: 746212 [0x0b62e4]

.FDR = PL_MMI3G_FPGA_9308_D1_08492A

.FDU = Userinfos zu FPGA 9308_D1_4010_10fv

** @0x801c0000: IFS [vers.1, UCL, old EMERGENCY]

total size: 4634856 [0x46b8e8]
- header: 256
- startup: 53512
- imagefs: 11553316

RAM: 11606828 [0xb11b2c]

** @0x80780000: IFS [vers.1, LZO, old APPLICATION]

total size:36655620 [0x22f5204]
- header: 256
- startup: 53512
- imagefs: 85393148

RAM: 85446660 [0x517d004]

** @0x87f00000: BIOS packet

total size: 524288 [0x080000]

BIOS pattern: FFFFFF7F.FFFFFFFF
App. pattern: FFFFFF7F.FFFFFFFF

=>
=> boot 1c0000
starting image @801c0000 ...

closep
=== UNEXPECTED EXCEPTION #180 !!!
- PC = 8801b53e
- PR = 8801479c
- SR = 400000f1
- R0 = 400000f0 R1 = 8801cc50 R2 = e500e498 R3 = ffeb0010
- R4 = 88013960 R5 = 801c0000 R6 = 100 R7 = 80009e30
- R8 = 4 R9 = 8801b540 R10 = c R11 = 8801cf00
- R12 = ffff R13 = 200 R14 = e50118c0 R15 = 8801cc08
================================================== ==============

IPL: Audi 3G 9308 (SH7785) / QNX 6.3.0 [PL_qnx_ipl-3g_9308-sh7785_07412A, built 2007/10/09_12-19-44_UTC]
CPU: SH7785 (>= 5th cut, clk mode 20), 792MHz
RAM: 512 MB (probed, DBCONF=e30002)
FLASH: Spansion S29GL512N: 512 sectors x 256K
FPGA: PL_MMI3G_FPGA_9308_D1_08492A
(0ms)
*** Old-fashioned mark found on IFS @0x1c0000: .zero=0x3000001d
*** Old-fashioned mark found on IFS @0x780000: .zero=0x10000000
starting image @780000 ...

closep
=== UNEXPECTED EXCEPTION #180 !!!
- PC = 8801b53e
- PR = 8801479c
- SR = 400000f1
- R0 = 400000f0 R1 = 8801cc50 R2 = e500e498 R3 = ffeb0010
- R4 = 88013960 R5 = 780000 R6 = 100 R7 = 80009e30
- R8 = 4 R9 = 8801b540 R10 = c R11 = 8801cf00
- R12 = ffff R13 = 40000 R14 = e5011e2c R15 = 8801cc08
================================================== ==============

IPL: Audi 3G 9308 (SH7785) / QNX 6.3.0 [PL_qnx_ipl-3g_9308-sh7785_07412A, built 2007/10/09_12-19-44_UTC]
CPU: SH7785 (>= 5th cut, clk mode 20), 792MHz
RAM: 512 MB (probed, DBCONF=e30002)
FLASH: Spansion S29GL512N: 512 sectors x 256K
FPGA: PL_MMI3G_FPGA_9308_D1_08492A
(0ms)
*** Old-fashioned mark found on IFS @0x1c0000: .zero=0x3000001d
*** Old-fashioned mark found on IFS @0x780000: .zero=0x10000000
starting image @780000 ...

closep

Tschako

20.07.2015, 22:32

OK, bad situation. Looks like a memory error in the flash area... no chance, I think!

you can try to flash an emg-ifs to the adress 780000 and start from IPL with "boot 780000"

Then try to reflash the emg-ifs from a FW-Card at 1c0000 with the flashit app

If it works, you can try again to boot the correct emg-ifs at 1c0000

good luck

a4ss4abt

20.07.2015, 23:03

Sorry, to try to flash an emg-ifs how can I do?
I Did a memory test please look:

ntering CLI, type '?' or 'help' for help

=> help
=> bconf
DBG_IF=scif.ffeb0000.115200.44000000.16
DIP=100
=> bios
BIOS: LZO uncompression to 0x8c000000
BIOS: Start BIOS @ 0x8c000000
closep
=== UNEXPECTED EXCEPTION #E0 !!!
- PC = 7
- PR = 880124ae
- SR = 600001f1
- R0 = 5 R1 = 7 R2 = 1 R3 = 8805e714
- R4 = ffe70032 R5 = f8 R6 = ffe70032 R7 = 7
- R8 = 8805e714 R9 = 880124c8 R10 = 88012488 R11 = 0
- R12 = 880122e4 R13 = a7f00000 R14 = e5011898 R15 = 882d7fd0
================================================== ==============

IPL: Audi 3G 9308 (SH7785) / QNX 6.3.0 [PL_qnx_ipl-3g_9308-sh7785_07412A, built 2007/10/09_12-19-44_UTC]
CPU: SH7785 (>= 5th cut, clk mode 20), 792MHz
RAM: 512 MB (probed, DBCONF=e30002)
FLASH: Spansion S29GL512N: 512 sectors x 256K
FPGA: PL_MMI3G_FPGA_9308_D1_08492A
(0ms)
*** Old-fashioned mark found on IFS @0x1c0000: .zero=0x3000001d
*** Old-fashioned mark found on IFS @0x780000: .zero=0x10000000
starting image @780000 ...

closep
=== UNEXPECTED EXCEPTION #180 !!!
- PC = 8801b53e
- PR = 8801479c
- SR = 400000f1
- R0 = 400000f0 R1 = 8801cc50 R2 = e500e498 R3 = ffeb0010
- R4 = 88013960 R5 = 780000 R6 = 100 R7 = 80009e30
- R8 = 4 R9 = 8801b540 R10 = c R11 = 8801cf00
- R12 = ffff R13 = 40000 R14 = e5011e2c R15 = 8801cc08
================================================== ==============

IPL: Audi 3G 9308 (SH7785) / QNX 6.3.0 [PL_qnx_ipl-3g_9308-sh7785_07412A, built 2007/10/09_12-19-44_UTC]
CPU: SH7785 (>= 5th cut, clk mode 20), 792MHz
RAM: 512 MB (probed, DBCONF=e30002)
FLASH: Spansion S29GL512N: 512 sectors x 256K
FPGA: PL_MMI3G_FPGA_9308_D1_08492A
(0ms)
*** Old-fashioned mark found on IFS @0x1c0000: .zero=0x3000001d
*** Old-fashioned mark found on IFS @0x780000: .zero=0x10000000
starting image @780000 ...

closep
=== UNEXPECTED EXCEPTION #180 !!!
- PC = 8801b53e
- PR = 8801479c
- SR = 400000f1
- R0 = 400000f0 R1 = 8801cc50 R2 = e500e498 R3 = ffeb0010
- R4 = 88013960 R5 = 780000 R6 = 100 R7 = 80009e30
- R8 = 4 R9 = 8801b540 R10 = c R11 = 8801cf00
- R12 = ffff R13 = 40000 R14 = e5011e2c R15 = 8801cc08
================================================== ==============

IPL: Audi 3G 9308 (SH7785) / QNX 6.3.0 [PL_qnx_ipl-3g_9308-sh7785_07412A, built 2007/10/09_12-19-44_UTC]
CPU: SH7785 (>= 5th cut, clk mode 20), 792MHz
RAM: 512 MB (probed, DBCONF=e30002)
FLASH: Spansion S29GL512N: 512 sectors x 256K
FPGA: PL_MMI3G_FPGA_9308_D1_08492A
(0ms)

Entering CLI, type '?' or 'help' for help

=> help
? - alias for 'help'
bconf - display boot manager configuration
bios - start BIOS
boot - boot image in memory/flash
diag_p1j - diagnostic for the PLL1 clock jitter problem
download - download IFS over serial line (sendnto protocol)
echo - echo args
fpga - load FPGA from image in memory/flash
go - jump to 'addr'
help - print online help
hwconf - dump hardware configuration
md - memory display
memperf - memory performance test (benchmark)
memtest - memory test
mt - alias for 'memtest'

=> memperf

READ (128 MB): unopt. C prefetch opt. ASM
------------------------------------------------------------------------
8192 * 16K 95ms [1379705K/s] 116ms [1129931K/s] 53ms [2473056K/s]
4096 * 32K 95ms [1379705K/s] 119ms [1101445K/s] 57ms [2299508K/s]
2048 * 64K 481ms [ 272498K/s] 210ms [ 624152K/s] 210ms [ 624152K/s]
1024 * 128K 481ms [ 272498K/s] 210ms [ 624152K/s] 210ms [ 624152K/s]
512 * 256K 481ms [ 272498K/s] 210ms [ 624152K/s] 210ms [ 624152K/s]
256 * 512K 481ms [ 272498K/s] 209ms [ 627138K/s] 209ms [ 627138K/s]
128 * 1024K 481ms [ 272498K/s] 209ms [ 627138K/s] 209ms [ 627138K/s]

WRITE (128 MB): unopt. C movca.l opt. ASM
------------------------------------------------------------------------
8192 * 16K 47ms [2788765K/s] 47ms [2788765K/s] 47ms [2788765K/s]
4096 * 32K 47ms [2788765K/s] 47ms [2788765K/s] 47ms [2788765K/s]
2048 * 64K 585ms [ 224054K/s] 99ms [1323959K/s] 99ms [1323959K/s]
1024 * 128K 585ms [ 224054K/s] 99ms [1323959K/s] 99ms [1323959K/s]
512 * 256K 585ms [ 224054K/s] 99ms [1323959K/s] 99ms [1323959K/s]
256 * 512K 585ms [ 224054K/s] 99ms [1323959K/s] 99ms [1323959K/s]
128 * 1024K 585ms [ 224054K/s] 99ms [1323959K/s] 99ms [1323959K/s]

FLASH (128 MB): unopt. C prefetch opt. ASM
------------------------------------------------------------------------
8192 * 16K 95ms [1379705K/s] 116ms [1129931K/s] 53ms [2473056K/s]
4096 * 32K 95ms [1379705K/s] 139ms [ 942964K/s] 77ms [1702233K/s]
2048 * 64K 1810ms [ 72415K/s] 1670ms [ 78486K/s] 1670ms [ 78486K/s]
1024 * 128K 1811ms [ 72375K/s] 1669ms [ 78533K/s] 1669ms [ 78533K/s]
512 * 256K 1811ms [ 72375K/s] 1668ms [ 78580K/s] 1668ms [ 78580K/s]
256 * 512K 1811ms [ 72375K/s] 1668ms [ 78580K/s] 1668ms [ 78580K/s]
128 * 1024K 1811ms [ 72375K/s] 1668ms [ 78580K/s] 1668ms [ 78580K/s]
=>

READ (128 MB): unopt. C prefetch opt. ASM
------------------------------------------------------------------------
8192 * 16K 95ms [1379705K/s] 116ms [1129931K/s] 53ms [2473056K/s]
4096 * 32K 95ms [1379705K/s] 119ms [1101445K/s] 57ms [2299508K/s]
2048 * 64K 481ms [ 272498K/s] 210ms [ 624152K/s] 210ms [ 624152K/s]
1024 * 128K 481ms [ 272498K/s] 210ms [ 624152K/s] 210ms [ 624152K/s]
512 * 256K 481ms [ 272498K/s] 210ms [ 624152K/s] 210ms [ 624152K/s]
256 * 512K 481ms [ 272498K/s] 209ms [ 627138K/s] 209ms [ 627138K/s]
128 * 1024K 481ms [ 272498K/s] 209ms [ 627138K/s] 209ms [ 627138K/s]

WRITE (128 MB): unopt. C movca.l opt. ASM
------------------------------------------------------------------------
8192 * 16K 47ms [2788765K/s] 47ms [2788765K/s] 47ms [2788765K/s]
4096 * 32K 47ms [2788765K/s] 47ms [2788765K/s] 47ms [2788765K/s]
2048 * 64K 585ms [ 224054K/s] 99ms [1323959K/s] 99ms [1323959K/s]
1024 * 128K 585ms [ 224054K/s] 99ms [1323959K/s] 99ms [1323959K/s]
512 * 256K 585ms [ 224054K/s] 99ms [1323959K/s] 99ms [1323959K/s]
256 * 512K 585ms [ 224054K/s] 99ms [1323959K/s] 99ms [1323959K/s]
128 * 1024K 585ms [ 224054K/s] 99ms [1323959K/s] 99ms [1323959K/s]

FLASH (128 MB): unopt. C prefetch opt. ASM
------------------------------------------------------------------------
8192 * 16K 95ms [1379705K/s] 116ms [1129931K/s] 53ms [2473056K/s]
4096 * 32K 95ms [1379705K/s] 139ms [ 942964K/s] 77ms [1702233K/s]
2048 * 64K 1810ms [ 72415K/s] 1670ms [ 78486K/s] 1670ms [ 78486K/s]
1024 * 128K 1811ms [ 72375K/s] 1669ms [ 78533K/s] 1669ms [ 78533K/s]
512 * 256K 1811ms [ 72375K/s] 1668ms [ 78580K/s] 1668ms [ 78580K/s]
256 * 512K 1811ms [ 72375K/s] 1668ms [ 78580K/s] 1668ms [ 78580K/s]
128 * 1024K 1811ms [ 72375K/s] 1668ms [ 78580K/s] 1668ms [ 78580K/s]
=> memttest
Unknown command 'memttest' - try 'help'
=> memtest
testing [48000000..4fffffff]: DDR_SS512_X_SCAN ......./......./....... PASSED.
=> fpga
missing/invalid argument/option
=> boot
missing/invalid argument/option
=> boot
missing/invalid argument/option
=> memtest
testing [48000000..4fffffff]: DDR_SS512_X_SCAN ......./......./....... PASSED.
=> memtest
testing [48000000..4fffffff]: DDR_SS512_X_SCAN ......./......./....... PASSED.
=>

a4ss4abt

20.07.2015, 23:12

Miracle!!!!

After that memtest it started and i saw on the screen the fw. v. 022 I tried the update to v. 257 from the SD but no luck when it re-boot to start the update i lost it again.

Tschako

20.07.2015, 23:12

show us a "scan" info right now

a4ss4abt

20.07.2015, 23:27

dead again with error #180

look the memory:

IPL: Audi 3G 9308 (SH7785) / QNX 6.3.0 [PL_qnx_ipl-3g_9308-sh7785_07412A, built 2007/10/09_12-19-44_UTC]
CPU: SH7785 (>= 5th cut, clk mode 20), 792MHz
RAM: 512 MB (probed, DBCONF=e30002)
FLASH: Spansion S29GL512N: 512 sectors x 256K
FPGA: PL_MMI3G_FPGA_9308_D1_08492A
(0ms)

Entering CLI, type '?' or 'help' for help

=> memtest
testing [48000000..4fffffff]: DDR_SS512_X_SCAN ......./ ** FAILED!
[@0x48004008: read 0x4b3a5e47, expected 0x4b3a5a47]
[db_t_rdata=0x3399d1b: read=067 write=067 dll=11b]
=> memperf

READ (128 MB): unopt. C prefetch opt. ASM
------------------------------------------------------------------------
8192 * 16K 95ms [1379705K/s] 116ms [1129931K/s] 53ms [2473056K/s]
4096 * 32K 95ms [1379705K/s] 119ms [1101445K/s] 57ms [2299508K/s]
2048 * 64K 481ms [ 272498K/s] 210ms [ 624152K/s] 210ms [ 624152K/s]
1024 * 128K 481ms [ 272498K/s] 210ms [ 624152K/s] 210ms [ 624152K/s]
512 * 256K 481ms [ 272498K/s] 210ms [ 624152K/s] 210ms [ 624152K/s]
256 * 512K 481ms [ 272498K/s] 209ms [ 627138K/s] 209ms [ 627138K/s]
128 * 1024K 481ms [ 272498K/s] 209ms [ 627138K/s] 209ms [ 627138K/s]

WRITE (128 MB): unopt. C movca.l opt. ASM
------------------------------------------------------------------------
8192 * 16K 47ms [2788765K/s] 47ms [2788765K/s] 47ms [2788765K/s]
4096 * 32K 47ms [2788765K/s] 47ms [2788765K/s] 47ms [2788765K/s]
2048 * 64K 585ms [ 224054K/s] 99ms [1323959K/s] 99ms [1323959K/s]
1024 * 128K 585ms [ 224054K/s] 99ms [1323959K/s] 99ms [1323959K/s]
512 * 256K 585ms [ 224054K/s] 99ms [1323959K/s] 99ms [1323959K/s]
256 * 512K 585ms [ 224054K/s] 99ms [1323959K/s] 99ms [1323959K/s]
128 * 1024K 585ms [ 224054K/s] 99ms [1323959K/s] 99ms [1323959K/s]

FLASH (128 MB): unopt. C prefetch opt. ASM
------------------------------------------------------------------------
8192 * 16K 95ms [1379705K/s] 116ms [1129931K/s] 53ms [2473056K/s]
4096 * 32K 95ms [1379705K/s] 139ms [ 942964K/s] 77ms [1702233K/s]
2048 * 64K 1810ms [ 72415K/s] 1670ms [ 78486K/s] 1670ms [ 78486K/s]
1024 * 128K 1811ms [ 72375K/s] 1669ms [ 78533K/s] 1669ms [ 78533K/s]
512 * 256K 1811ms [ 72375K/s] 1668ms [ 78580K/s] 1668ms [ 78580K/s]
256 * 512K 1811ms [ 72375K/s] 1668ms [ 78580K/s] 1668ms [ 78580K/s]
128 * 1024K 1811ms [ 72375K/s] 1668ms [ 78580K/s] 1668ms [ 78580K/s]
=> memperf

READ (128 MB): unopt. C prefetch opt. ASM
------------------------------------------------------------------------
8192 * 16K 95ms [1379705K/s] 116ms [1129931K/s] 53ms [2473056K/s]
4096 * 32K 95ms [1379705K/s] 119ms [1101445K/s] 57ms [2299508K/s]
2048 * 64K 481ms [ 272498K/s] 210ms [ 624152K/s] 210ms [ 624152K/s]
1024 * 128K 481ms [ 272498K/s] 210ms [ 624152K/s] 210ms [ 624152K/s]
512 * 256K 481ms [ 272498K/s] 210ms [ 624152K/s] 210ms [ 624152K/s]
256 * 512K 481ms [ 272498K/s] 209ms [ 627138K/s] 209ms [ 627138K/s]
128 * 1024K 481ms [ 272498K/s] 209ms [ 627138K/s] 209ms [ 627138K/s]

WRITE (128 MB): unopt. C movca.l opt. ASM
------------------------------------------------------------------------
8192 * 16K 47ms [2788765K/s] 47ms [2788765K/s] 47ms [2788765K/s]
4096 * 32K 47ms [2788765K/s] 47ms [2788765K/s] 47ms [2788765K/s]
2048 * 64K 585ms [ 224054K/s] 99ms [1323959K/s] 99ms [1323959K/s]
1024 * 128K 585ms [ 224054K/s] 99ms [1323959K/s] 99ms [1323959K/s]
512 * 256K 585ms [ 224054K/s] 99ms [1323959K/s] 99ms [1323959K/s]
256 * 512K 585ms [ 224054K/s] 99ms [1323959K/s] 99ms [1323959K/s]
128 * 1024K 585ms [ 224054K/s] 99ms [1323959K/s] 99ms [1323959K/s]

FLASH (128 MB): unopt. C prefetch opt. ASM
------------------------------------------------------------------------
8192 * 16K 95ms [1379705K/s] 116ms [1129931K/s] 53ms [2473056K/s]
4096 * 32K 95ms [1379705K/s] 139ms [ 942964K/s] 77ms [1702233K/s]
2048 * 64K 1810ms [ 72415K/s] 1670ms [ 78486K/s] 1670ms [ 78486K/s]
1024 * 128K 1811ms [ 72375K/s] 1669ms [ 78533K/s] 1669ms [ 78533K/s]
512 * 256K 1811ms [ 72375K/s] 1668ms [ 78580K/s] 1668ms [ 78580K/s]
256 * 512K 1811ms [ 72375K/s] 1668ms [ 78580K/s] 1668ms [ 78580K/s]
128 * 1024K 1811ms [ 72375K/s] 1668ms [ 78580K/s] 1668ms [ 78580K/s]
=>

READ (128 MB): unopt. C prefetch opt. ASM
------------------------------------------------------------------------
8192 * 16K 95ms [1379705K/s] 116ms [1129931K/s] 53ms [2473056K/s]
4096 * 32K 95ms [1379705K/s] 119ms [1101445K/s] 57ms [2299508K/s]
2048 * 64K 481ms [ 272498K/s] 210ms [ 624152K/s] 210ms [ 624152K/s]
1024 * 128K 481ms [ 272498K/s] 210ms [ 624152K/s] 210ms [ 624152K/s]
512 * 256K 481ms [ 272498K/s] 210ms [ 624152K/s] 210ms [ 624152K/s]
256 * 512K 481ms [ 272498K/s] 209ms [ 627138K/s] 209ms [ 627138K/s]
128 * 1024K 481ms [ 272498K/s] 209ms [ 627138K/s] 209ms [ 627138K/s]

WRITE (128 MB): unopt. C movca.l opt. ASM
------------------------------------------------------------------------
8192 * 16K 47ms [2788765K/s] 47ms [2788765K/s] 47ms [2788765K/s]
4096 * 32K 47ms [2788765K/s] 47ms [2788765K/s] 47ms [2788765K/s]
2048 * 64K 585ms [ 224054K/s] 99ms [1323959K/s] 99ms [1323959K/s]
1024 * 128K 585ms [ 224054K/s] 99ms [1323959K/s] 99ms [1323959K/s]
512 * 256K 585ms [ 224054K/s] 99ms [1323959K/s] 99ms [1323959K/s]
256 * 512K 585ms [ 224054K/s] 99ms [1323959K/s] 99ms [1323959K/s]
128 * 1024K 585ms [ 224054K/s] 99ms [1323959K/s] 99ms [1323959K/s]

FLASH (128 MB): unopt. C prefetch opt. ASM
------------------------------------------------------------------------
8192 * 16K 95ms [1379705K/s] 116ms [1129931K/s] 53ms [2473056K/s]
4096 * 32K 95ms [1379705K/s] 139ms [ 942964K/s] 77ms [1702233K/s]
2048 * 64K 1810ms [ 72415K/s] 1670ms [ 78486K/s] 1670ms [ 78486K/s]
1024 * 128K 1811ms [ 72375K/s] 1669ms [ 78533K/s] 1669ms [ 78533K/s]
512 * 256K 1811ms [ 72375K/s] 1668ms [ 78580K/s] 1668ms [ 78580K/s]
256 * 512K 1811ms [ 72375K/s] 1668ms [ 78580K/s] 1668ms [ 78580K/s]
128 * 1024K 1811ms [ 72375K/s] 1668ms [ 78580K/s] 1668ms [ 78580K/s]
=> memtest
testing [48000000..4fffffff]: DDR_SS512_X_SCAN ......./ ** FAILED!
[@0x48004008: read 0x4b3a5e47, expected 0x4b3a5a47]
[db_t_rdata=0x3319918: read=066 write=066 dll=118]
=> memtest
testing [48000000..4fffffff]: DDR_SS512_X_SCAN ......./......./....... PASSED.
=> memtest
testing [48000000..4fffffff]: DDR_SS512_X_SCAN ......./......./....... PASSED.
=> memtest
testing [48000000..4fffffff]: DDR_SS512_X_SCAN ......./ ** FAILED!
[@0x48004008: read 0x4b3a5e47, expected 0x4b3a5a47]
[db_t_rdata=0x3299515: read=065 write=065 dll=115]
=> memtest
testing [48000000..4fffffff]: DDR_SS512_X_SCAN ......./ ** FAILED!
[@0x48004008: read 0x4b3a5e47, expected 0x4b3a5a47]
[db_t_rdata=0x3319916: read=066 write=066 dll=116]
=> memtest
testing [48000000..4fffffff]: DDR_SS512_X_SCAN ......./ ** FAILED!
[@0x48004008: read 0x4b3a5e47, expected 0x4b3a5a47]
[db_t_rdata=0x3319916: read=066 write=066 dll=116]
=> memtest
testing [48000000..4fffffff]: DDR_SS512_X_SCAN ......./......./....... PASSED.
=> memtest
testing [48000000..4fffffff]: DDR_SS512_X_SCAN ......./ ** FAILED!
[@0x48004008: read 0x4b3a5e47, expected 0x4b3a5a47]
[db_t_rdata=0x3299515: read=065 write=065 dll=115]
=>

Tschako

21.07.2015, 19:33

Whats abaout the output after the "scan" command at the ipl prompt??

a4ss4abt

21.07.2015, 19:50

Sorry I didn't understand that you asked for the "scan" command... I will send you if I will be able to launch in IPL cause it immediately starts with the error now.

Tschako

21.07.2015, 21:18

If you start the unit (with pressed ground-switch) then type "scan" and show us the result of the command...

a4ss4abt

21.07.2015, 21:33

a4ss4abt

21.07.2015, 21:39

MIRACLE IT STARTED!!
iT is re-doing the update now!!

Crash-100

21.07.2015, 21:46

testing [48000000..4fffffff]: DDR_SS512_X_SCAN ......./ ** FAILED!
I was right !!!!! :applause: This trible is very hard to FIX. you must change 4 DRAM - DDR chip.

a4ss4abt

21.07.2015, 22:06

Where to find those DDR???

testing [48000000..4fffffff]: DDR_SS512_X_SCAN ......./ ** FAILED!
I was right !!!!! :applause: This trible is very hard to FIX. you must change 4 DRAM - DDR chip.

a4ss4abt

21.07.2015, 22:36

Second Miracle!!!

a4ss4abt

21.07.2015, 23:01

No unfortunately it is dead....it begins the emergency update but it cannot finish!!!

a4ss4abt

22.07.2015, 00:01

IPL: Audi 3G 9308 (SH7785) / QNX 6.3.0 [PL_qnx_ipl-3g_9308-sh7785_07412A, built 2007/10/09_12-19-44_UTC]
CPU: SH7785 (>= 5th cut, clk mode 20), 792MHz
RAM: 512 MB (probed, DBCONF=e30002)
FLASH: Spansion S29GL512N: 512 sectors x 256K
FPGA: PL_MMI3G_FPGA_9308_D1_08492A
(0ms)
*** emergency FPGA loaded!
*** Old-fashioned mark found on IFS @0x1c0000: .zero=0x3000001e
starting image @1c0000 ...

Startup: PL_qnx_startup-sh7785_08362A, built 2008/09/02_07-53-12_UTC
RAM : 256 MB @0x08000000
FLASH: 128 MB @0x00000000

System page at phys:0800a000 user:0800a000 kern:8800a000
Starting next program at v88046840
------------------------------------------------------
Welcome to QNX 6.3.2 (RL_qnx_os_632_PSP3_08124A) MMI3G Audi EMERGENCY SETUP 9308 D1 09431A
starting pci driver
*** init FPGA registers ***
starting dev-ipc for IOC
initialize IPC Driver
starting network driver
starting atapi driver - setup device /dev/cam0
Path=0 - XILINX MMI3G_8
target=0 lun=0 CD-ROM(5) - FJ-TEN DVD-ROM DV-04FT1 Rev: 1422
Path=1 - XILINX MMI3G_8
target=1 lun=0 Direct-Access(0) - TOSHIBA MK4036GA Rev: TA15
starting devc-pty
starting flash driver
starting SDCard driver
Path=0 -
target=0 lun=0 Direct-Access(0) - SD08G Rev: 5.1
Unable to access "/dev/io-net/en5" (2)
starting with no network driver
================================================== =========
Emergency IFS is started. Emergency app tries to restore
the application.
================================================== =========
49169 running /usr/bin/devg-NVTIRM
DMA is Disabled
dma disabled, interrupt thread priority = 100
49171 running /sbin/io-media-nvidia
49172 running /usr/sbin/io-display
49173 running /usr/apps/MMI3GEmergencyApp
================================================== =========
Emergency shell started, fix your system and restart again
================================================== =========
discplayer_init: IN
nvidia_render_manager_init: IN
INvmRenderManager::GetNvmRenderManager (&pRenderManager);
er = pRenderManager->Init(oConfig);
# Fpga header is not 0x4744482e (0xffffffff)!
App FPGA valid 0
Emergency FPGA valid 1
Disabling IOC watchdog

EmergencyApp-MMI3G: version 22.30.1642, date of build 14.10.2009
pRenderManager->Open()
nvidia_render_manager_init: OUT
discplayer_init: OUT
discplayer_init
discplayer_init: IN
nvidia_render_manager_init: IN
nvidia_render_manager_init: OUT
discplayer_init: OUT
dvdtrackplayer_init
discplayer_init: IN
nvidia_render_manager_init: IN
nvidia_render_manager_init: OUT
discplayer_init: OUT
dvdnavigator_init
created navigator control point with 8249288
mixer_init: IN
mixer_init: OUT
NvTRACELEVEL set to 3 (Level Info)
nVAudio_init: IN
nvidia_render_manager_init();
nvidia_render_manager_init: IN
nvidia_render_manager_init: OUT
nVAudio_init: OUT
installing audio decoders
installing video decoders
nVAudio_init: IN
nvidia_render_manager_init();
nvidia_render_manager_init: IN
nvidia_render_manager_init: OUT
nVAudio_init: OUT
OnIpcGetCaptureUnitSourceCount
Number of displays: 6
Number of layers: 9
Graphics init was successfull: DisplaySize is 800x 480
Set DisplayStatus to 2
OnOff: process IPC event HWsample 209 HWvariant 7 FinalShutdown 0
SWDL: startUpdate HW index 209, variant 9307
OnOff: phase Scan metainfo
FPGA info is complete. Orphaned headers are already deleted (if there were any).
scan for info: 40000: ff ff ff ff 92
scan for info: 40001: ff ff ff 92 29
scan for info: 40002: ff ff 92 29 92
scan for info: 40003: ff 92 29 92 29
scan for info: 40004: 92 29 92 29 40
scan for info: 40005: 29 92 29 40 53
scan for info: 40006: 92 29 40 53 57
scan for info: 40007: 29 40 53 57 44
scan for info: 40008: 40 53 57 44 4c
searchInfo 1
FPGA info header @SWDL V1@
FPGA info version 1
FPGA info variant 9307
FPGA info HW index MU 41
FPGA info region Europe
FPGA info step 0
FPGA info HW index IT 0
FPGA info ignore region/variant 0
FPGA info loop 0
FPGA info repeat 0
FPGA info CRC c4f9299d
SWDL: Stopping EFS driver!
slay: Unable to find process 'checkPersistence'
result of running command stop_efs_driver.sh is 0
SWDL: Starting EFS driver (automount)!
(devf t1::f3s_recover_boot:141) fs0p1 boot P[E0] U: 58
result of running command start_efs_driver.sh is 0
/HBpersistence/SWDL not found!
(devf t1::f3s_recover_boot:141) fs0p3 boot P[1A8] U: 74
/HBpersistence/SWDL not found!
/HBpersistence/SWDL not found!
/HBpersistence/SWDL not found!
Use update.txt from persistence
update.txt: CRC = bf6d8c04
update.txt: MetafileCRC = b324595b
update.txt: Use DSIv2 = true
update.txt: AssemblyID = 0
update.txt: ReleaseName = HNav_EU_K0257_5_D1
update.txt: Source = SD1
update.txt: Path = /
update.txt: ReleasePath =
update.txt: UseSubDir = 1
update.txt: MaxSubDir = 3
update.txt: CurrentStep = 1
update.txt: Phase3Device = MuIOC
update.txt: [DVD\0\Main\14\default\bootloader]=NO;0;default;0
update.txt: [DVD\0\Main\14\default\application]=TODO;1319424;default;1319680
update.txt: [MU9307\0\fpga\41\default\bootloader]=NO;0;default;0
update.txt: [MU9307\0\fpga\41\default\application]=TODO;1642;default;2020
update.txt: [MU9307\0\fpga-emg\41\default\bootloader]=NO;0;default;0
update.txt: [MU9307\0\fpga-emg\41\default\application]=NO;1642;default;1642
update.txt: [MU9307\0\ifs-emg\41\default\bootloader]=NO;0;default;0
update.txt: [MU9307\0\ifs-emg\41\default\application]=TODO;29;default;30
update.txt: [MU9307\0\ifs-root\41\default\bootloader]=NO;0;default;0
update.txt: [MU9307\0\ifs-root\41\default\application]=TODO;792;default;956
update.txt: [MU9307\0\efs-system\41\default\bootloader]=NO;0;default;0
update.txt: [MU9307\0\efs-system\41\default\application]=TODO;792;default;956
update.txt: [MU9307\0\efs-persist\41\default\bootloader]=NO;0;default;0
update.txt: [MU9307\0\efs-persist\41\default\application]=NO;324;default;324
update.txt: [MuIOC\0\Main\41\default\bootloader]=TODO;786;default;789
update.txt: [MuIOC\0\Main\41\default\application]=TODO;1368;default;1546
update.txt: [MuINIC\0\Main\41\default\bootloader]=NO;0;default;0
update.txt: [MuINIC\0\Main\41\default\application]=NO;17827601;default;17827601
update.txt: [DUA130\0\Front\41\default\bootloader]=NO;0;default;0
update.txt: [DUA130\0\Front\41\default\application]=NO;104;default;104
update.txt: [MuGPS\0\Main\41\default\bootloader]=NO;0;default;0
update.txt: [MuGPS\0\Main\41\default\application]=NO;500;default;500
update.txt: [MuTnrRef\0\data\0\default\File]=TODO;630;default;811
update.txt: [MUConsistency\0\Data\0\default\File]=TODO;47;default;143
update.txt: [sss\0\general\0\default\Dir]=NO;58;default;58
update.txt: [sss\0\recog de_DE\0\default\Dir]=NO;46;default;46
update.txt: [sss\0\recog en_GB\0\default\Dir]=NO;45;default;45
update.txt: [sss\0\recog es_ES\0\default\Dir]=NO;45;default;45
update.txt: [sss\0\recog fr_FR\0\default\Dir]=NO;45;default;45
update.txt: [sss\0\recog it_IT\0\default\Dir]=NO;46;default;46
update.txt: [sss\0\recog nl_NL\0\default\Dir]=NO;45;default;45
update.txt: [sss\0\recog pt_PT\0\default\Dir]=NO;45;default;45
update.txt: [sss\0\recog en_SA\0\default\Dir]=NO;45;default;45
update.txt: [sss\0\tts de_DE\0\default\Dir]=NO;35;default;35
update.txt: [sss\0\tts en_GB\0\default\Dir]=NO;32;default;32
update.txt: [sss\0\tts es_ES\0\default\Dir]=NO;32;default;32
update.txt: [sss\0\tts fr_FR\0\default\Dir]=NO;31;default;31
update.txt: [sss\0\tts it_IT\0\default\Dir]=NO;33;default;33
update.txt: [sss\0\tts nl_NL\0\default\Dir]=NO;32;default;32
update.txt: [sss\0\tts pt_PT\0\default\Dir]=NO;31;default;31
update.txt: [sss\0\tts en_SA\0\default\Dir]=NO;33;default;33
update.txt: [sss\0\tts ru_RU\0\default\Dir]=NO;34;default;34
update.txt: [MapStyles\0\ECE04\0\default\File]=NO;60;default;60
update.txt: [MapStyles\0\ME04\0\default\File]=NO;60;default;60
update.txt: [MapStyles\0\HM04\0\default\File]=NO;60;default;60
update.txt: [MapStyles\0\ASIA04\0\default\File]=NO;60;default;60
update.txt: [MapStyles\0\SA04\0\default\File]=NO;60;default;60
update.txt: [MapStyles\0\AN04\0\default\File]=NO;60;default;60
OnOff: variant 9307
OnOff: DeviceName MU9307
Import: Sourcepath = /, ReleasePath = , SubDir = 1/3, Step = 1
Src: Medialauncher is running
Src: mount OK
SWDL: mount OK
SWDL: open metainfo /metainfo2.txt
SWDL: open finished (19921)
OnOff: FileAccess for continues!
OnOff: Current file access type: read
SWDL: read finished (19921, 0)
SWDL: parse metainfo
SWDL: use metainfo
OnOff: region 'Europe'
Old image[0]: ipl 0, 0x0 0x40000
Old image[1]: fpga 1, 0x40000 0xc0000
Old image[2]: fpga-emg 2, 0x100000 0xc0000
Old image[3]: ifs-emg 5, 0x1c0000 0x4733ac
New image[0]: ipl 0, 0x0 0xf720
New image[1]: fpga 1, 0x40000 0xb63e8
New image[2]: fpga-emg 2, 0x100000 0xb63e8
New image[3]: ifs-emg 5, 0x1c0000 0x4733ac
New image[4]: ifs-root 3, 0x780000 0x231b10c
New image[5]: efs-extended 6, 0x3800000 0x1600000
New image[6]: efs-system 6, 0x4e00000 0x1400000
New image[7]: efs-persist 6, 0x6200000 0x1d00000
SWDL: Stopping EFS driver!
slay: Unable to find process 'checkPersistence'
result of running command stop_efs_driver.sh is 0
SWDL: Starting EFS driver (no automount)!
result of running command start_efs_driver.sh -a is 0
OnOff: Max images 8
SWDL: open file /MU9308/ifs-root/41/default/ifs-root.ifs
OnOff: image release version 2020
OnOff: image release version 1642
OnOff: image release version 30
dev_fd == 12
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0x780000
limit: 0x40000
OnOff: image release version 956
SWDL: open finished (36811020)
OnOff: image name ifs-root
OnOff: image index 4
OnOff: phase Erase
OnOff: Progress 000

a4ss4abt

22.07.2015, 00:06

SWDL: read finished (524288, 0)
devctl(12,-2146694912,xx,12,0) returned 0SWDL: read finished (524288, 524288)
dev_fd == 12
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0x7c0000
limit: 0x40000
SWDL: read finished (524288, 1048576)
SWDL: read finished (524288, 1572864)
SWDL: read finished (524288, 2097152)
SWDL: read finished (524288, 2621440)
SWDL: read finished (524288, 3145728)
devctl(12,-2146694912,xx,12,0) returned 0OnOff: Progress 001
dev_fd == 12
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0x800000
limit: 0x40000
SWDL: read finished (524288, 3670016)
SWDL: read finished (524288, 4194304)
SWDL: read finished (524288, 4718592)
SWDL: read finished (524288, 5242880)
SWDL: read finished (524288, 5767168)
SWDL: read finished (524288, 6291456)
devctl(12,-2146694912,xx,12,0) returned 0OnOff: Progress 002
dev_fd == 12
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0x840000
limit: 0x40000
SWDL: read finished (524288, 6815744)
SWDL: read finished (524288, 7340032)
SWDL: read finished (524288, 7864320)
SWDL: read finished (524288, 8388608)
SWDL: read finished (524288, 8912896)
SWDL: read finished (524288, 9437184)
devctl(12,-2146694912,xx,12,0) returned 0dev_fd == 12
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0x880000
limit: 0x40000
SWDL: read finished (524288, 9961472)
SWDL: read finished (524288, 10485760)
SWDL: read finished (524288, 11010048)
SWDL: read finished (524288, 11534336)
SWDL: read finished (524288, 12058624)
SWDL: read finished (524288, 12582912)
devctl(12,-2146694912,xx,12,0) returned 0OnOff: Progress 003
dev_fd == 12
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0x8c0000
limit: 0x40000
SWDL: read finished (524288, 13107200)
SWDL: read finished (524288, 13631488)
SWDL: read finished (524288, 14155776)
SWDL: read finished (524288, 14680064)
SWDL: read finished (524288, 15204352)
devctl(12,-2146694912,xx,12,0) returned 0SWDL: read finished (524288, 15728640)
OnOff: Progress 004
dev_fd == 12
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0x900000
limit: 0x40000
SWDL: read finished (524288, 16252928)
SWDL: read finished (524288, 16777216)
SWDL: read finished (524288, 17301504)
SWDL: read finished (524288, 17825792)
SWDL: read finished (524288, 18350080)
devctl(12,-2146694912,xx,12,0) returned 0dev_fd == 12
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0x940000
limit: 0x40000
SWDL: read finished (524288, 18874368)
SWDL: read finished (524288, 19398656)
SWDL: read finished (524288, 19922944)
SWDL: read finished (524288, 20447232)
SWDL: read finished (524288, 20971520)
SWDL: read finished (524288, 21495808)
devctl(12,-2146694912,xx,12,0) returned 0OnOff: Progress 005
dev_fd == 12
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0x980000
limit: 0x40000
SWDL: read finished (524288, 22020096)
SWDL: read finished (524288, 22544384)
SWDL: read finished (524288, 23068672)
SWDL: read finished (524288, 23592960)
SWDL: read finished (524288, 24117248)
devctl(12,-2146694912,xx,12,0) returned 0SWDL: read finished (524288, 24641536)
OnOff: Progress 006
dev_fd == 12
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0x9c0000
limit: 0x40000
SWDL: read finished (524288, 25165824)
SWDL: read finished (524288, 25690112)
SWDL: read finished (524288, 26214400)
SWDL: read finished (524288, 26738688)
SWDL: read finished (524288, 27262976)
SWDL: read finished (524288, 27787264)
devctl(12,-2146694912,xx,12,0) returned 0OnOff: Progress 007
dev_fd == 12
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0xa00000
limit: 0x40000
SWDL: read finished (524288, 28311552)
SWDL: read finished (524288, 28835840)
SWDL: read finished (524288, 29360128)
SWDL: read finished (524288, 29884416)
SWDL: read finished (524288, 30408704)
SWDL: read finished (524288, 30932992)
devctl(12,-2146694912,xx,12,0) returned 0dev_fd == 12
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0xa40000
limit: 0x40000
SWDL: read finished (524288, 31457280)
SWDL: read finished (524288, 31981568)
SWDL: read finished (524288, 32505856)
SWDL: read finished (524288, 33030144)
SWDL: read finished (524288, 33554432)
devctl(12,-2146694912,xx,12,0) returned 0SWDL: read finished (524288, 34078720)
OnOff: Progress 008
dev_fd == 12
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0xa80000
limit: 0x40000
SWDL: read finished (524288, 34603008)
SWDL: read finished (524288, 35127296)
SWDL: read finished (524288, 35651584)
SWDL: read finished (524288, 36175872)
SWDL: read finished (110860, 36700160)
devctl(12,-2146694912,xx,12,0) returned 0OnOff: Progress 009
dev_fd == 11
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0xac0000
limit: 0x40000
devctl(11,-2146694912,xx,12,0) returned 0dev_fd == 11
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0xb00000
limit: 0x40000
devctl(11,-2146694912,xx,12,0) returned 0OnOff: Progress 010
dev_fd == 11
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0xb40000
limit: 0x40000
devctl(11,-2146694912,xx,12,0) returned 0OnOff: Progress 011
dev_fd == 11
devctl returned 0
arrayinfo.unit_size 262144

a4ss4abt

22.07.2015, 00:08

calling devctl with erase struct:
status: 0
offset: 0xb80000
limit: 0x40000
devctl(11,-2146694912,xx,12,0) returned 0OnOff: Progress 012
dev_fd == 11
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0xbc0000
limit: 0x40000
devctl(11,-2146694912,xx,12,0) returned 0dev_fd == 11
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0xc00000
limit: 0x40000
devctl(11,-2146694912,xx,12,0) returned 0OnOff: Progress 013
dev_fd == 11
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0xc40000
limit: 0x40000
devctl(11,-2146694912,xx,12,0) returned 0OnOff: Progress 014
dev_fd == 11
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0xc80000
limit: 0x40000
devctl(11,-2146694912,xx,12,0) returned 0dev_fd == 11
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0xcc0000
limit: 0x40000
devctl(11,-2146694912,xx,12,0) returned 0OnOff: Progress 015
dev_fd == 11
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0xd00000
limit: 0x40000
devctl(11,-2146694912,xx,12,0) returned 0OnOff: Progress 016
dev_fd == 11
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0xd40000
limit: 0x40000
devctl(11,-2146694912,xx,12,0) returned 0OnOff: Progress 017
dev_fd == 11
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0xd80000
limit: 0x40000
devctl(11,-2146694912,xx,12,0) returned 0dev_fd == 11
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0xdc0000
limit: 0x40000
devctl(11,-2146694912,xx,12,0) returned 0OnOff: Progress 018
dev_fd == 11
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0xe00000
limit: 0x40000
devctl(11,-2146694912,xx,12,0) returned 0OnOff: Progress 019
dev_fd == 11
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0xe40000
limit: 0x40000
devctl(11,-2146694912,xx,12,0) returned 0dev_fd == 11
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0xe80000
limit: 0x40000
devctl(11,-2146694912,xx,12,0) returned 0OnOff: Progress 020
dev_fd == 11
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0xec0000
limit: 0x40000
devctl(11,-2146694912,xx,12,0) returned 0OnOff: Progress 021
dev_fd == 11
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0xf00000
limit: 0x40000
devctl(11,-2146694912,xx,12,0) returned 0dev_fd == 11
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0xf40000
limit: 0x40000
devctl(11,-2146694912,xx,12,0) returned 0OnOff: Progress 022
dev_fd == 11
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0xf80000
limit: 0x40000
devctl(11,-2146694912,xx,12,0) returned 0OnOff: Progress 023
dev_fd == 11
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0xfc0000
limit: 0x40000
devctl(11,-2146694912,xx,12,0) returned 0dev_fd == 11
OnOff: Progress 024
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0x1000000
limit: 0x40000
devctl(11,-2146694912,xx,12,0) returned 0dev_fd == 11
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0x1040000
limit: 0x40000
devctl(11,-2146694912,xx,12,0) returned 0OnOff: Progress 025
dev_fd == 11
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0x1080000
limit: 0x40000
devctl(11,-2146694912,xx,12,0) returned 0OnOff: Progress 026
dev_fd == 11
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0x10c0000
limit: 0x40000
devctl(11,-2146694912,xx,12,0) returned 0dev_fd == 11
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0x1100000
limit: 0x40000
devctl(11,-2146694912,xx,12,0) returned 0OnOff: Progress 027
dev_fd == 11
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0x1140000
limit: 0x40000
devctl(11,-2146694912,xx,12,0) returned 0OnOff: Progress 028
dev_fd == 11
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0x1180000
limit: 0x40000
devctl(11,-2146694912,xx,12,0) returned 0OnOff: Progress 029
dev_fd == 11
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0x11c0000
limit: 0x40000
devctl(11,-2146694912,xx,12,0) returned 0dev_fd == 11
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0x1200000
limit: 0x40000
closep
=== MANUAL RESET
- PC = 88009404
- PR = 8804a86e
- SR = 700000f0
- R0 = ffffffea R1 = c1 R2 = c1 R3 = 2cc
- R4 = 880817cc R5 = 97feb000 R6 = 30 R7 = c1
- R8 = 8804a812 R9 = fff R10 = 97834a20 R11 = 88009328
- R12 = c1 R13 = c1 R14 = 8804a778 R15 = 88009328
================================================== ==============

IPL: Audi 3G 9308 (SH7785) / QNX 6.3.0 [PL_qnx_ipl-3g_9308-sh7785_07412A, built 2007/10/09_12-19-44_UTC]
CPU: SH7785 (>= 5th cut, clk mode 20), 792MHz
RAM: 512 MB (probed, DBCONF=e30002)
FLASH: Spansion S29GL512N: 512 sectors x 256K
FPGA: PL_MMI3G_FPGA_9308_D1_08492A
(0ms)
*** emergency FPGA loaded!
*** Old-fashioned mark found on IFS @0x1c0000: .zero=0x3000001e
starting image @1c0000 ...

closep
=== UNEXPECTED EXCEPTION #180 !!!
- PC = 8801b53e
- PR = 8801479c
- SR = 400000f1
- R0 = 400000f0 R1 = 8801cc50 R2 = e500e498 R3 = ffeb0010
- R4 = 88013960 R5 = 1c0000 R6 = 100 R7 = 80009e30
- R8 = 4 R9 = 8801b540 R10 = c R11 = 8801cf00
- R12 = ffff R13 = 100000 R14 = e5011e2c R15 = 8801cc08
================================================== ==============

IPL: Audi 3G 9308 (SH7785) / QNX 6.3.0 [PL_qnx_ipl-3g_9308-sh7785_07412A, built 2007/10/09_12-19-44_UTC]
CPU: SH7785 (>= 5th cut, clk mode 20), 792MHz
RAM: 512 MB (probed, DBCONF=e30002)
FLASH: Spansion S29GL512N: 512 sectors x 256K
FPGA: PL_MMI3G_FPGA_9308_D1_08492A
(0ms)
*** emergency FPGA loaded!
*** Old-fashioned mark found on IFS @0x1c0000: .zero=0x3000001e
starting image @1c0000 ...

closep
=== UNEXPECTED EXCEPTION #180 !!!
- PC = 8801b53e
- PR = 8801479c
- SR = 400000f1
- R0 = 400000f0 R1 = 8801cc50 R2 = e500e498 R3 = ffeb0010
- R4 = 88013960 R5 = 1c0000 R6 = 100 R7 = 80009e30
- R8 = 4 R9 = 8801b540 R10 = c R11 = 8801cf00
- R12 = ffff R13 = 100000 R14 = e5011e2c R15 = 8801cc08
================================================== ==============

IPL: Audi 3G 9308 (SH7785) / QNX 6.3.0 [PL_qnx_ipl-3g_9308-sh7785_07412A, built 2007/10/09_12-19-44_UTC]

Crash-100

22.07.2015, 10:02

No unfortunately it is dead....it begins the emergency update but it cannot finish!!!

)))))))))))))))))))))))))))))))))))))
Your devece have damaged 4 pcs 1GB DDR chip, you have to change them!

a4ss4abt

22.07.2015, 23:37

Certainly not so easy to do!
I would understand where to find them also!!

Crash-100

24.07.2015, 14:30

inside MMI four black chip on the ball.

aboky

10.08.2015, 12:46

Всем привет! MMI 3G после перезагрузки 3 кнопками( зависла навигация)- погасла, черный экран , подсветка не включается. Диагностика выдает ошибки нет коммуникации с 5F, Radio и Instrument Cluster. Но IC диагностируется! Может кто помочь советом?

Crash-100

10.08.2015, 13:08

aboky

10.08.2015, 19:56

я думаю нужно говорить о том, что ты делал до ресета!
Машина ехала начала зависать навигация перезагрузил, заработала.Через минут 10 снова заглючила перезагрузил и в ответ черный экран!

Deamoon

13.08.2015, 16:39

Доброго времени суток всем. Ситуация похожая как постом выше, туарег RNS850, ехал человек, глючила нави, перезапустил сам клиент 3-4 раза, и все черный экран и нет связи) Есть у кого какие советы или предложения? Спасибо.

Crash-100

13.08.2015, 18:22

Совет один отдать тому, кто понимает, пишите, где находитесь территориально, возможно найдутся те, кто решит Вашу проблему.

Deamoon

13.08.2015, 19:17

Готов поговорить об удаленном решении на коммерческой основе, в лс, программаторы всевозможные, инфракраска и руки имеются. Предложения в лс. Спасибо.

Crash-100

13.08.2015, 20:36

город

Deamoon

13.08.2015, 21:55

Калининград

Hoto

17.08.2015, 19:18

Добрый день
Нужен дамп с живой ММИ для 9308.

Ginny.kmv

23.09.2015, 18:42

Привет !MMI 3G как говорят не доделаный 4E0035646 Что я уже голову сломал не получается нормального отзыва от головы . Зеленый экран гаснит при соединении и в терминале ересть полная . Помогите пожалййста

Crash-100

23.09.2015, 18:49

А что ты делал и что значит зеленый экран гаснет при соединении.

Ginny.kmv

23.09.2015, 19:00

Мне такой автос пригнали . Клиент ни колется что делал , говорит просто утром зеленый экран увидел и все тут . на мотиторе надпись MMI3G EmApp 21.27.1642 AppFPGA in valid ! We will do nothing !
Я разобрал припоял три проводка и подключил к адаптору UART что нашел у нас в магазине видео наблюдения ) другого не было (
А в терминале ироглефы (
А гаснет при перезагрузке экран

Crash-100

23.09.2015, 19:08

пока проблем не вижу, все как и должно быть, режим восстановления, а терминал - разбирайся, проблема не в MMI.

Ginny.kmv

23.09.2015, 19:12

Если все как и должно быть почему в флешки не начинатся обновление ? Может не то сую ?

Crash-100

23.09.2015, 19:17

Ну я не ясновидящий, какой у тебя аппарат, какой софт ты ему даешь, какой в его запихнули, это тебе на TNT.

Ginny.kmv

23.09.2015, 19:26

Без HDD без навигации и без блютуса . Понятно что не ясновидящий . Вам а этке пробить ? что стоит или так по номерам сказать можно ) Если конечно помочь хотите . ? Не надо смотреть на 2 поста на этом форуме . Да признаю тут я полный огрызок ну что поделать (

Crash-100

23.09.2015, 23:17

нужен лог

Ginny.kmv

24.09.2015, 14:13

Привет ! Вот лог . но там я хз кракозяблы)
Не могу что то прикрепить вот что в файле

ааааааяж~`шxffжжюшf~ю`юююшжfаf ?юа?жюxxxxю~жаf~ю``ю`ююx~`жю`аЌ©`� �жfxаюxffаxx?~жажюxxжfxf``юfю`fxfаxxж x`xа~xюжю~f`~`юxx`x`~xжxf~fx~xff~fшf`fюжf fжюxжx`юаfxжfюf~`юшf~`юш?f~xюfжа~x?f юfюfxаюfx?жюжжю`~f~~ffжажшf~~юxxxж� �fюжxжffаюxж`ю```юxжжажxfx~xажюfжx юxfш`юfxfюжfаfжюfxfxffxаfжшжfаfffаxx ж~жxжxа~xxюfшfююжюxxжжfюжжжюжж� �`юшжfаfжюf?ююfж`~`жж?шжxж~жю`?а� �аfю`?x?fю`юfюfю

Crash-100

24.09.2015, 16:30

Чем я могу тебе помочь, пришли, помогу.
Еще раз повторюсь, дело не в MMI.

Ginny.kmv

24.09.2015, 16:46

Наткните меня на нужную прошивку , плиз

Crash-100

24.09.2015, 16:49

вычитай из MMI какая версия была удали через терминал SWDL и всунь SD с нужной версией!

Ginny.kmv

24.09.2015, 19:13

Как это сделать ? я вообще что то отдуплится не могу ...... Можно по удаленке за вознагрождение ! Скайп ginny.kmv

Ginny.kmv

01.10.2015, 22:52

Привет ! Люди добрые подскажите как получают вот такое в окне терминала , я голову уже сломал (

У меня эроглифы мать их ........ А у людей вот смотрю у всех типа этого
IPL: Audi 3G 9308 (SH7785) / QNX 6.3.0 [PL_qnx_ipl-3g_9308-sh7785_07412A, built 2007/10/09_12-19-44_UTC]
CPU: SH7785 (>= 5th cut, clk mode 20), 792MHz
RAM: 512 MB (probed, DBCONF=e30002)
FLASH: Spansion S29GL512N: 512 sectors x 256K
FPGA: PL_MMI3G_FPGA_9308_D1_08492A
(0ms)
*** Old-fashioned mark found on IFS @0x1c0000: .zero=0x3000001d
*** Old-fashioned mark found on IFS @0x780000: .zero=0x10000000
starting image @780000 ...

closep
=== UNEXPECTED EXCEPTION #180 !!!
- PC = 8801b53e
- PR = 8801479c
- SR = 400000f1
- R0 = 400000f0 R1 = 8801cc50 R2 = e500e498 R3 = ffeb0010
- R4 = 88013960 R5 = 780000 R6 = 100 R7 = 80009e30
- R8 = 4 R9 = 8801b540 R10 = c R11 = 8801cf00

Как этого добиться ?

Ginny.kmv

01.10.2015, 23:28

О боже свершшилось )) Настройки порта (скорость ) это пипец я уже кучу шнурков напаял )

Зgetdipclose*** could not load FPGA image @40000: DONE pin low after programming
IPL: 3G_9304 / QNX 6.3.0 [PL_qnx_ipl-3g_9304_07284A, built 2007/07/12_09-15-16_UTC]
CPU: SH7785 (>= 5th cut, clk mode 16), 594MHz
RAM: 256 MB (probed, DBCONF=db0002)
FLASH: Spansion S29GL512N: 512 sectors x 256K
FPGA: PL_MMI3G_FPGA_9302_D1_08492A
(0ms)
*** emergency FPGA loaded!
*** Old-fashioned mark found on IFS @0x1c0000: .zero=0x3000001b
starting image @1c0000 ...

Startup: PL_qnx_startup-sh7785_08362A, built 2008/09/02_07-53-12_UTC
RAM : 256 MB @0x08000000
FLASH: 128 MB @0x00000000

System page at phys:0800a000 user:0800a000 kern:8800a000
Starting next program at v88046840
------------------------------------------------------
Welcome to QNX 6.3.2 (RL_qnx_os_632_PSP3_08124A) MMI3G Audi EMERGENCY SETUP 9302 D1 09034A
starting pci driver
*** init FPGA registers ***
starting dev-ipc for IOC
initialize IPC Driver
starting network driver
starting i2c and devb-sercd-hbfpga driver - setup device /dev/cd0
starting devc-pty
starting flash driver
Path=0 - QSSL SERCD
target=0 lun=0 CD-ROM(5) - Philips CDM-M8 Rev: 45N
starting SDCard driver
Path=0 -
target=0 lun=0 Direct-Access(0) - NCard Rev: 1.0
Unable to access "/dev/io-net/en5" (2)
starting with no network driver
================================================== =========
Emergency IFS is started. Emergency app tries to restore
the application.
================================================== =========
49170 running /usr/sbin/io-display
49170 exited with status 0
53267 running /usr/apps/MMI3GEmergencyApp
================================================== =========
Emergency shell started, fix your system and restart again
================================================== =========
# App FPGA valid 1
Emergency FPGA valid 1

EmergencyApp-MMI3G: version 21.27.1642, date of build 14.01.2009
Number of displays: 1
Number of layers: 3
Graphics init was successfull: DisplaySize is 400x 240
The FPGA for the application is valid!
getdipclose*** could not load FPGA image @40000: DONE pin low after programming
IPL: 3G_9304 / QNX 6.3.0 [PL_qnx_ipl-3g_9304_07284A, built 2007/07/12_09-15-16_UTC]
CPU: SH7785 (>= 5th cut, clk mode 16), 594MHz
RAM: 256 MB (probed, DBCONF=db0002)
FLASH: Spansion S29GL512N: 512 sectors x 256K
FPGA: PL_MMI3G_FPGA_9302_D1_08492A
(0ms)
*** emergency FPGA loaded!
*** Old-fashioned mark found on IFS @0x1c0000: .zero=0x3000001b
starting image @1c0000 ...

Startup: PL_qnx_startup-sh7785_08362A, built 2008/09/02_07-53-12_UTC
RAM : 256 MB @0x08000000
FLASH: 128 MB @0x00000000

System page at phys:0800a000 user:0800a000 kern:8800a000
Starting next program at v88046840
------------------------------------------------------
Welcome to QNX 6.3.2 (RL_qnx_os_632_PSP3_08124A) MMI3G Audi EMERGENCY SETUP 9302 D1 09034A
starting pci driver
*** init FPGA registers ***
starting dev-ipc for IOC
initialize IPC Driver
starting network driver
starting i2c and devb-sercd-hbfpga driver - setup device /dev/cd0
starting devc-pty
starting flash driver
Path=0 - QSSL SERCD
target=0 lun=0 CD-ROM(5) - Philips CDM-M8 Rev: 45N
starting SDCard driver
Path=0 -
target=0 lun=0 Direct-Access(0) - NCard Rev: 1.0
Unable to access "/dev/io-net/en5" (2)
starting with no network driver
================================================== =========
Emergency IFS is started. Emergency app tries to restore
the application.
================================================== =========
49170 running /usr/sbin/io-display
49170 exited with status 0
53267 running /usr/apps/MMI3GEmergencyApp
================================================== =========
Emergency shell started, fix your system and restart again
================================================== =========
# App FPGA valid 1
Emergency FPGA valid 1

EmergencyApp-MMI3G: version 21.27.1642, date of build 14.01.2009
Number of displays: 1
Number of layers: 3
Graphics init was successfull: DisplaySize is 400x 240
The FPGA for the application is valid!

А вот что теперь подскажите пожалуйста .

Ginny.kmv

02.10.2015, 12:40

Привет ! Видимо сам с сабой все же ((

Подскажите диск который шел до 8R0906961Q , этот не стартует , хотя обновы

Timur_ua

07.10.2015, 09:13

Привет, был у меня еепром на ку 7 с симкой европейской и пропал куда то ))) может удалил случайно ничего не пойму )
киньте пожалуйста в меня таким еепромом на 3g plus. Спасибо.

Abush

07.10.2015, 12:53

IPL: Audi 3G 9308 (SH7785) / QNX 6.3.0 [PL_qnx_ipl-3g_9308-sh7785_07412A, built 2007/10/09_12-19-44_UTC]
CPU: SH7785 (>= 5th cut, clk mode 20), 792MHz
RAM: 512 MB (probed, DBCONF=e30002)
FLASH: Spansion S29GL512N: 512 sectors x 256K
FPGA: PL_MMI3G_FPGA_9308_D1_08142A (0ms)
*** emergency FPGA loaded!
*** Old-fashioned mark found on IFS @0x780000: .zero=0x10000000
*** ERROR: No valid IFS image @ffffffff !!!

Entering CLI, type '?' or 'help' for help

IPL: Audi 3G 9308 (SH7785) / QNX 6.3.0 [PL_qnx_ipl-3g_9308-sh7785_07412A, built 2007/10/09_12-19-44_UTC]
CPU: SH7785 (>= 5th cut, clk mode 20), 792MHz
RAM: 512 MB (probed, DBCONF=e30002)
FLASH: Spansion S29GL512N: 512 sectors x 256K
FPGA: PL_MMI3G_FPGA_9308_D1_08142A (0ms)
*** emergency FPGA loaded!
*** Old-fashioned mark found on IFS @0x780000: .zero=0x10000000
*** ERROR: No valid IFS image @ffffffff !!!

Entering CLI, type '?' or 'help' for help

IPL: Audi 3G 9308 (SH7785) / QNX 6.3.0 [PL_qnx_ipl-3g_9308-sh7785_07412A, built 2007/10/09_12-19-44_UTC]
CPU: SH7785 (>= 5th cut, clk mode 20), 792MHz
RAM: 512 MB (probed, DBCONF=e30002)
FLASH: Spansion S29GL512N: 512 sectors x 256K
FPGA: PL_MMI3G_FPGA_9308_D1_08142A (0ms)
*** emergency FPGA loaded!
*** Old-fashioned mark found on IFS @0x780000: .zero=0x10000000
*** ERROR: No valid IFS image @ffffffff !!!

Entering CLI, type '?' or 'help' for help

IPL: Audi 3G 9308 (SH7785) / QNX 6.3.0 [PL_qnx_ipl-3g_9308-sh7785_07412A, built 2007/10/09_12-19-44_UTC]
CPU: SH7785 (>= 5th cut, clk mode 20), 792MHz
RAM: 512 MB (probed, DBCONF=e30002)
FLASH: Spansion S29GL512N: 512 sectors x 256K
FPGA: PL_MMI3G_FPGA_9308_D1_08142A (0ms)
*** emergency FPGA loaded!
*** Old-fashioned mark found on IFS @0x780000: .zero=0x10000000
*** ERROR: No valid IFS image @ffffffff !!!

Entering CLI, type '?' or 'help' for help

=> boot780000
Unknown command 'boot780000' - try 'help'
=> boot 780000
starting image @80780000 ...

Startup: PL_qnx_startup-sh7785_Rel07252A_08105A, built 2008/03/07_17-24-06_UTC
RAM: 100 MB @0x08000000
NVRAM: 28 MB @0x0e400000
RAM: 128 MB @0x40000000
RAM: 256 MB @0x50000000
FLASH: 128 MB @0x00000000

System page at phys:0800a000 user:0800a000 kern:8800a000
Starting next program at v8804a7e0
Welcome QNX6.3.2 (QNXLabel RL_qnx_os_632_PSP3_08041A)- Harman/Becker MMI3G Build 9307/08 D1-08241A
USB-stuff (QNXLabel RL_qnx_os_632_PSP3_08041A)
[proc_tracker_run_test]
s: 0
v: 0
r: 0
m: 0
mkprocsymlinks 0.10, reading /mnt/ifs-root/etc/system/efs_symlinks.cfg
done
s: 0
v: 0
r: 0
m: 0
mkprocsymlinks 0.10, reading /mnt/ifs-root/etc/system/ifs-root_symlinks.cfg
done
starting server starter...
# multicored [000000001.030]:version 4.0.o, verbosity 1 (supported 4), scope 0x00000001, console: /dev/ser1 (fd=3)
NVLOADER: Booting DSP (DRAM Setup time = 1000 us)...
multicored [000000001.061]:attached to filesystem at /hbsystem/multicore, port 851
NVLOADER: Going to call nvTsrmRawLoad for file /etc/NvDspCodecs.elf
multicored [000000001.064]:MACHINE:SH(1), total MEM 507510784, 1: 271582976 SH7785 (SH4A) 792MHz, FPU
multicored [000000001.064]:sloop active
multicored [000000001.066]:lo0 127.0.0.1 255.0.0.0
NVLOADER: Done
Enabling DMA using channel 7
Overriding default Interrupt Priority
Current debug level = 0x7fffffff
dmaChannel = 7, interrupt thread priority = 21
multicored [000000001.570]:listener on port 851 active, fd=7
devg-NVMEM: Mapped vaddr 0x38100000 to paddr 0x5ca4f000
dev-nvram: PL_qnx_dev-nvram_07225A, built 2007/06/01_15-43-18_UTC
dev-nvram: page_size:4096
dev-nvram: signalling register 10ee:9308:0:40:40 [vid:did:bar:offs:mask]
dev-nvram: CPU: SH7785 (5th cut or higher, clk_mode 20) [10300700:240, 133735fa]
dev-nvram: map '/dev/nvram/navi' to 0xe400000-0xfffefff
dev-nvram: map '/dev/nvram/.guard' to 0xffff000-0xfffffff
dev-nvram: SelfRefresh was inactive
UART: Mod:0E Date:07411A Ver:2.0.3
devc-ser8250hb: UART supports FiFo counter
devc-ser8250hb: UART supports 32bit access
devc-ser8250hb: RX_FIFO_SIZE:512 TX_FIFO_SIZE:512
devc-ser8250hb: set IBUF size to 4096
UART: Mod:0E Date:07411A Ver:2.0.3
devc-ser8250hb: UART supports FiFo counter
devc-ser8250hb: RX_FIFO_SIZE:32 TX_FIFO_SIZE:32
UART: Mod:0E Date:07411A Ver:2.0.3
devc-ser8250hb: UART supports FiFo counter
devc-ser8250hb: RX_FIFO_SIZE:32 TX_FIFO_SIZE:32
Debug filehandle = 4
For further debug messages have a look at multicore output consoles '/hbsystem/multicore/navi/g'
Mask = c3
GPIO 7 set to = Low
[track(prc) 1 6 10 88078c2e]
[track(cli) 40985 1 10 70335f1a]
Overriding default Interrupt Priority

io-media-nvidia built: Jun 2 2008 15:47:06 against Official Tree

nv_global.verbose = 0

Virtual Address for CDDA DirectIO = 8390000
NEDL: Acquiring Capture Unit
NEDL: Acquiring Layer
NEDL: Switching source to 0 (Format = PAL)
NvRender: Reconfigure Video Port to PAL
NEDL: Switching source to 0 (Format = PAL)
Path=0 - XILINX MMI3G_8
target=0 lun=0 CD-ROM(5) - FJ-TEN DVD-ROM DV-04FT1 Rev: 1422
Path=1 - XILINX MMI3G_8
target=1 lun=0 Direct-Access(0) - TOSHIBA MK4036GA Rev: TA15
cd0 mounted after 1 try
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
multicored [000000041.426]:debuglevel changed to 1, connection /hbsystem/multicore
multicored [000000041.427]:startup phase ending for 0
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88072e36]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88072e40]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 53272 8 15 70335e52]
[track(prc) 1 1 0 88072e42]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 32774 2 30 703360be]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
^A[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]

No such file or directory
# [track(prc) 1 1 0 88078c2e]
boot[track(prc) 1 1 0 88078c2e]
b[track(prc) 1 1 0 88078c2e]
oot 1c[track(prc) 32774 2 30 7035356c]
0000
No such file or directory
# [track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c28]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]
[track(prc) 1 1 0 88078c2e]

Abush

07.10.2015, 12:55

Всем привет . Помогите с ремонтом
На нее установили не то обновление. Теперь не знаю что можно сделать . Как ни пытаюсь не чего не получается .

Romanov

30.10.2015, 20:47

Добрый вечер. Мое почтение всем, а в особенности Сергею, так как его прошивка стояла на моей любимой Шкоде. помогите советом: Обновляли Q5, variant 9307. Прошивка стояла P0022 Поставили нормально 8R0906961T (0031) Начали ставить 8R0906961AS (0260) и из-за диска и невозможности его проитать, обновление прервалось. Потом появился зеленый и красные экраны. По итогу появилось зеленый экран: http://i.piccy.info/i9/e324d8a8ce115772edcaba23f7fc774c/1446228277/137486/965950/cBiX0nSQ_kA.jpg (EmmApp 22.30.1642) Scan metinfo Please wait. И ВСЕ. Никаких изменений после этого. Пробовали поставить диск с версией 0031, пишет CRC check error. Ставим другие диски, картинка не меняется... В целом уже прочитал весь форум и примерно понимаю что делать. Не могли бы ва более детально обьяснить? Спасибо.

Crash-100

30.10.2015, 20:49

удали папку SWDL

Romanov

30.10.2015, 20:50

Все получилось. Через терминал, с помощью команды rm удалили все директории, файлы из папки SWDL, перезагрузили с новейшей прошивкой в SD слоте, после этого через инженерку обновили еще раз недостающие блоки и все работает! Благодарен за наводку. Будете в Крыму или Лос Анжелесе - телеграфируйте! :)

DiveManiac

02.11.2015, 01:14

Создал отдельную тему, но думаю, надо было запостить сюда. Помогите пожалуйста с проблемой с MMI http://turbo-quattro.com/showthread.php?21668-%D0%9F%D0%BE%D0%BB%D0%BD%D0%BE%D1%81%D1%82%D1%8C%D 1%8E-%D0%B7%D0%B0%D0%B2%D0%B8%D1%81%D0%BB%D0%B0-mmi3g

Vlasoff

19.11.2015, 15:16

удали папку SWDL

если убить ее на рабочей голове, что случится после перезапуска?
Точнее вопрос, за что отвечают папки внутри? Кроме истории апдейтов

trawqu

26.12.2015, 23:26

с помощью команды rm удалили все директории, файлы из папки SWDL
I don't speek russian..Please write in english, what is comad ?

kaon

27.12.2015, 09:58

имею mmi от А6С7 2011 г.в.
Пытался активировать новые карты, не дождался окончания работы скрипта, перезагрузил и все - мми померла.
Вот лог патча, который остался на SD - "Patch Started. Copying Dumper script Dumper script copyed. Copying application "

заказал вот этот переходник - http://ru.aliexpress.com/item/FT232R...710443569.html (http://ru.aliexpress.com/item/FT232RL-FT232-USB-UART-PCB-converter-with-Data-TTL-Serial-Module/710443569.html)

мои действия:
-подпаиваюсь к ламелькам порта на мми как указано на фото мануала
-подключаю концы по схеме мми TxD - RxD переходник
GRD - GRD
RxD - TxD
- включаю мми в машине, подсоединив все порты ,включая оптику
- подключаюсь к компу, запускаю teraterm
- замыкаю RxD с мми на GRD переходника
- после перезапуска головы ввожу последовательно команды:
mount -uw /mnt/efs-persist/
rm /mnt/efs-persist/MMI3GApplication

Я правильно все описал?

и ещё - прошивка стоит 900-я....будут ли проблемы с отзывом мми на команды терминала?....
Есть информация, что Emergency Update не доступна на K900

Crash-100

27.12.2015, 12:22

если убить ее на рабочей голове, что случится после перезапуска?
Точнее вопрос, за что отвечают папки внутри? Кроме истории апдейтов
Привет!
Земля круглая )))
Как раз таки в этой папке и лежит все по обновлению текущему и прошлым, на работоспособность головы никак не влияет.

Crash-100

27.12.2015, 12:31

имею mmi от А6С7 2011 г.в.
Пытался активировать новые карты, не дождался окончания работы скрипта, перезагрузил и все - мми померла.
Вот лог патча, который остался на SD - "Patch Started. Copying Dumper script Dumper script copyed. Copying application "

заказал вот этот переходник - http://ru.aliexpress.com/item/FT232R...710443569.html (http://ru.aliexpress.com/item/FT232RL-FT232-USB-UART-PCB-converter-with-Data-TTL-Serial-Module/710443569.html)
мои действия:
-подпаиваюсь к ламелькам порта на мми как указано на фото мануала
-подключаю концы по схеме мми TxD - RxD переходник
GRD - GRD
RxD - TxD
- включаю мми в машине, подсоединив все порты ,включая оптику
- подключаюсь к компу, запускаю teraterm
- замыкаю RxD с мми на GRD переходника
- после перезапуска головы ввожу последовательно команды:
mount -uw /mnt/efs-persist/
rm /mnt/efs-persist/MMI3GApplication

Я правильно все описал?

и ещё - прошивка стоит 900-я....будут ли проблемы с отзывом мми на команды терминала?....
Есть информация, что Emergency Update не доступна на K900
Terminal под паролем, Emagency еще нет, но по видимому будет как в MIB и запуск скриптов закроют.

kaon

27.12.2015, 13:30

Crash-100, пароль известен? Или можно его обойти?

Romanov

27.12.2015, 14:51

trawqu

27.12.2015, 15:03

You need to learn unix commands lik "ls" or "rm" and few others, and delete everything what inside that directory including subdirectories. Its not hard. Just be sure what those actions will solve your problem instead of making it worse.

Thank You very much. It was not until I begin to repair MMi 3G. I have a terminal and everything works.
I had the same problem like post 405

Romanov

28.12.2015, 06:15

Well if you sure what you have same problem as me at post #405 - just delete everything inside that directory and update to latest firmware. My problem gone after ive done it.

trawqu

28.12.2015, 09:56

Thanks .
Cany you give me some example comand.?

kaon

09.01.2016, 12:43

вводил команды:
boot 1c0000
flashit -a 40000 -e 1000

получил вот это:

IPL: Audi 3G 9308 (SH7785) / QNX 6.3.0 [PL_qnx_ipl-3g_9308-sh7785_08253A, built 2008/06/18_15-16-25_UTC]
CPU: SH7785 (>= 5th cut, clk mode 20. 4xDDR), 792MHz
RAM: 512 MB (probed, DBCONF=e30002)
FLASH: Spansion S29GL512N (32bit): 512 sectors x 256K
FPGA: PL_MMI3G_PLUS_FPGA_9411_D1_09422A
(0ms)
*** emergency FPGA loaded!

Entering CLI, type '?' or 'help' for help

=> boot 1c0000
starting image @801c0000 ...

Startup: PL_qnx_startup-sh7785_09332A, built 2009/08/11_11-10-29_UTC
RAM : 128 MB @0x08000000
RAM : 128 MB @0x40000000
RAM : 256 MB @0x50000000
FLASH: 128 MB @0x00000000
FPGA IRQ: Interrupt Controller ID:33 Ver:2.1.0 ILVL:7 Lines:255

System page at phys:0800a000 user:0800a000 kern:8800a000
Starting next program at v88046b20
intrentry_base = 8ffe5630, size=2176
copying intrentry code:
intrentry_code_buf = 88085f28
intrentry_base = 8ffe5630
copy_size = 2432
final intrentry_base = 8ffe5630, size=2176
------------------------------------------------------
Welcome to QNX 6.3.2 (RL_qnx_os_632_PSP3_09423A) MMI3G Audi EMERGENCY SETUP 14194A
starting pci driver
*** init FPGA registers ***
[pcidma] PL_qnx_pcidma_FMod08363A_09274A, built 2009/07/02_11-10-37_UTC
starting dev-ipc for IOC
initialize IPC Driver
starting network driver
starting atapi driver - setup device /dev/cam0
starting devc-pty
starting flash driver
Path=0 - XILINX ATAPI
target=0 lun=0 CD-ROM(5) - FJ-TEN DVD-ROM DV-05FT2 Rev: 1B20
Path=1 - XILINX ATAPI
target=1 lun=0 Direct-Access(0) - TOSHIBA MK6050GA Rev: TJ10
starting SDCard driver
Path=0 -
target=0 lun=0 Direct-Access(0) - SDC Rev: 0.2
Unable to access "/dev/io-net/en5" (2)
starting with no network driver
================================================== =========
Emergency IFS is started. Emergency app tries to restore
the application.
================================================== =========
49169 running /usr/bin/devg-NVTIRM
DMA is Disabled
dma disabled, interrupt thread priority = 100
49171 running /sbin/io-media-nvidia
49172 running /usr/sbin/io-display
49173 running /usr/apps/MMI3GEmergencyApp
================================================== =========
Emergency shell started, fix your system and restart again
================================================== =========
discplayer_init: IN
nvidia_render_manager_init: IN
INvmRenderManager::GetNvmRenderManager (&pRenderManager);
er = pRenderManager->Init(oConfig);
# Fpga header is not 0x4744482e (0xffffffff)!
App FPGA valid 0
Emergency FPGA valid 1
Disabling IOC watchdog

EmergencyApp-MMI3G: version 35.24.2098, date of build 08.05.2014
pRenderManager->Open()
nvidia_render_manager_init: OUT
discplayer_init: OUT
discplayer_init
discplayer_init: IN
nvidia_render_manager_init: IN
nvidia_render_manager_init: OUT
discplayer_init: OUT
dvdtrackplayer_init
discplayer_init: IN
nvidia_render_manager_init: IN
nvidia_render_manager_init: OUT
discplayer_init: OUT
dvdnavigator_init
created navigator control point with 8249288
mixer_init: IN
mixer_init: OUT
NvTRACELEVEL set to 3 (Level Info)
nVAudio_init: IN
nvidia_render_manager_init();
nvidia_render_manager_init: IN
nvidia_render_manager_init: OUT
nVAudio_init: OUT
installing audio decoders
installing video decoders
nVAudio_init: IN
nvidia_render_manager_init();
nvidia_render_manager_init: IN
nvidia_render_manager_init: OUT
nVAudio_init: OUT
OnIpcGetCaptureUnitSourceCount
Number of displays: 6
Number of layers: 9
Graphics init was successfull: DisplaySize is 800x 480
Set DisplayStatus to 2
OnOff: process IPC event HWsample 209 HWvariant 111 FinalShutdown 0
SWDL: startUpdate HW index 209, variant 9411
OnOff: phase Scan metainfo
FPGA info is complete. Orphaned headers are already deleted (if there were any).
skipFile /HBpersistence/SWDL/Log/service/1/DirInfo.z 147
skipFile /HBpersistence/SWDL/Log/service/1/General.z 256
skipFile /HBpersistence/SWDL/Log/service/1/PreSWDL.z 517
skipFile /HBpersistence/SWDL/Log/service/1/PostSWDL.z 1507
skipFile /HBpersistence/SWDL/Log/service/2/DirInfo.z 2638
skipFile /HBpersistence/SWDL/Log/service/2/General.z 2752
skipFile /HBpersistence/SWDL/Log/service/2/PreSWDL.z 3140
skipFile /HBpersistence/SWDL/Log/service/2/PostSWDL.z 4123
skipFile /HBpersistence/SWDL/Log/service/3/DirInfo.z 5288
skipFile /HBpersistence/SWDL/Log/service/3/General.z 5399
skipFile /HBpersistence/SWDL/Log/service/3/PreSWDL.z 5662
skipFile /HBpersistence/SWDL/Log/service/3/PostSWDL.z 6817
skipFile /HBpersistence/SWDL/Log/service/4/DirInfo.z 8041
skipFile /HBpersistence/SWDL/Log/service/4/General.z 8155
skipFile /HBpersistence/SWDL/Log/service/4/PreSWDL.z 8543
skipFile /HBpersistence/SWDL/Log/service/4/PostSWDL.z 9415
skipFile /HBpersistence/SWDL/Log/service/5/DirInfo.z 10443
skipFile /HBpersistence/SWDL/Log/service/5/General.z 10558
skipFile /HBpersistence/SWDL/Log/service/5/PreSWDL.z 10947
skipFile /HBpersistence/SWDL/Log/service/5/PostSWDL.z 11897
skipFile /HBpersistence/SWDL/Log/service/6/DirInfo.z 13016
skipFile /HBpersistence/SWDL/Log/service/6/General.z 13125
skipFile /HBpersistence/SWDL/Log/service/6/PreSWDL.z 13386
skipFile /HBpersistence/SWDL/Log/service/6/PostSWDL.z 14521
skipFile /HBpersistence/SWDL/Log/service/7/DirInfo.z 15726
skipFile /HBpersistence/SWDL/Log/service/7/General.z 15833
skipFile /HBpersistence/SWDL/Log/service/7/PreSWDL.z 16093
skipFile /HBpersistence/SWDL/Log/service/7/PostSWDL.z 17246
skipFile /HBpersistence/SWDL/Log/service/8/DirInfo.z 18522
skipFile /HBpersistence/SWDL/Log/service/8/General.z 18637
skipFile /HBpersistence/SWDL/Log/service/8/PreSWDL.z 19026
skipFile /HBpersistence/SWDL/Log/service/8/PostSWDL.z 19976
skipFile /HBpersistence/SWDL/Log/SubDirsIndex.txt.z 21093
skipFile /HBpersistence/SWDL/Log/SubDirsRestart.txt.z 21165
skipFile /HBpersistence/SWDL/Log/RepeatCo.unt.z 21239
skipFile /HBpersistence/SWDL/Log/CfgAck.z 21307
skipFile /HBpersistence/SWDL/Log/SvmOld.z 21370
skipFile /HBpersistence/SWDL/Log/SvmInfoIgnoreImages.txt 21846
skipFile /HBpersistence/SWDL/region.txt.z 21943
skipFile /HBpersistence/SWDL/MuRingType.txt 22005
skipFile /HBpersistence/SWDL/info/MuVariant.txt.z 22070
skipFile /HBpersistence/SWDL/info/MuHwIndex.txt.z 22139
skipFile /HBpersistence/SWDL/info/MuRegion.txt.z 22208
skipFile /HBpersistence/SWDL/info/IgnoreRegionVariant.txt.z 22276
extractFile /HBpersistence/SWDL/IT/hwIndex.txt /dev/shmem/HBpersistence_SWDL_IT_hwIndex.txt 0x5754
skipFile /HBpersistence/SWDL/FileCopyInfo/AudiSupportedFscs.info 22412
skipFile /HBpersistence/SWDL/FileCopyInfo/MuTnrRef.info 22580
skipFile /HBpersistence/SWDL/FileCopyInfo/MUConsistency.info 22720
skipFile /HBpersistence/SWDL/FileCopyInfo/GEMMI.info 22883
skipFile /HBpersistence/SWDL/FileCopyInfo/sss.info 23001
skipFile /HBpersistence/SWDL/FileCopyInfo/MapStyles.info 24398
skipFile /HBpersistence/SWDL/FileCopyInfo/TMCConfig.info 25576
skipFile /HBpersistence/SWDL/FileCopyInfo/NaviPersistence.info 25778
skipFile /HBpersistence/SWDL/FileCopyInfo/AUDI_MMI3G_ECE.info 26037
skipFile /HBpersistence/SWDL/MainUnit-version2.txt 27660
skipFile /HBpersistence/SWDL/MainUnit-version2.txt.SWDL.version.txt 30451
skipFile /HBpersistence/SWDL/MainUnit-version2.txt.SWDL.compatibility.txt 30542
skipFile /HBpersistence/SWDL/update.txt.Abort.old 30632
skipFile /HBpersistence/SWDL/Emergency/FpgaOK 37409
skipFile /HBpersistence/FSC/cache/00040008.fsc 37728
skipFile /HBpersistence/FSC/cache/00040009.fsc 37786
skipFile /HBpersistence/FSC/Logs/Security_Exceptions.log 37844
skipFile /HBpersistence/FSC/00040009.fsc 44812
skipFile /HBpersistence/FSC/0004000A.fsc 45066
fillInfoFromFpga: MU
scan for info: 0x40000: ff ff ff ff 92 29 92 29 40 53 57 44 4c 20 56 31
searchInfo 1
FPGA info header @SWDL V1@
FPGA info version 1
FPGA info variant 9411
FPGA info type Main Unit
FPGA info HW index 41
FPGA info region <noRegion>
FPGA info step 0
FPGA info HW index IT 0
FPGA info ignore region/variant 0
FPGA info loop 0
FPGA info repeat 0
FPGA info CRC 89bfd4b
Set DisplayStatus to 4

kaon

09.01.2016, 12:48

skipFile /HBpersistence/SWDL/Log/service/1/DirInfo.z 147
skipFile /HBpersistence/SWDL/Log/service/1/General.z 256
skipFile /HBpersistence/SWDL/Log/service/1/PreSWDL.z 517
skipFile /HBpersistence/SWDL/Log/service/1/PostSWDL.z 1507
skipFile /HBpersistence/SWDL/Log/service/2/DirInfo.z 2638
skipFile /HBpersistence/SWDL/Log/service/2/General.z 2752
skipFile /HBpersistence/SWDL/Log/service/2/PreSWDL.z 3140
skipFile /HBpersistence/SWDL/Log/service/2/PostSWDL.z 4123
skipFile /HBpersistence/SWDL/Log/service/3/DirInfo.z 5288
skipFile /HBpersistence/SWDL/Log/service/3/General.z 5399
skipFile /HBpersistence/SWDL/Log/service/3/PreSWDL.z 5662
skipFile /HBpersistence/SWDL/Log/service/3/PostSWDL.z 6817
skipFile /HBpersistence/SWDL/Log/service/4/DirInfo.z 8041
skipFile /HBpersistence/SWDL/Log/service/4/General.z 8155
skipFile /HBpersistence/SWDL/Log/service/4/PreSWDL.z 8543
skipFile /HBpersistence/SWDL/Log/service/4/PostSWDL.z 9415
skipFile /HBpersistence/SWDL/Log/service/5/DirInfo.z 10443
skipFile /HBpersistence/SWDL/Log/service/5/General.z 10558
skipFile /HBpersistence/SWDL/Log/service/5/PreSWDL.z 10947
skipFile /HBpersistence/SWDL/Log/service/5/PostSWDL.z 11897
skipFile /HBpersistence/SWDL/Log/service/6/DirInfo.z 13016
skipFile /HBpersistence/SWDL/Log/service/6/General.z 13125
skipFile /HBpersistence/SWDL/Log/service/6/PreSWDL.z 13386
skipFile /HBpersistence/SWDL/Log/service/6/PostSWDL.z 14521
skipFile /HBpersistence/SWDL/Log/service/7/DirInfo.z 15726
skipFile /HBpersistence/SWDL/Log/service/7/General.z 15833
skipFile /HBpersistence/SWDL/Log/service/7/PreSWDL.z 16093
skipFile /HBpersistence/SWDL/Log/service/7/PostSWDL.z 17246
skipFile /HBpersistence/SWDL/Log/service/8/DirInfo.z 18522
skipFile /HBpersistence/SWDL/Log/service/8/General.z 18637
skipFile /HBpersistence/SWDL/Log/service/8/PreSWDL.z 19026
skipFile /HBpersistence/SWDL/Log/service/8/PostSWDL.z 19976
skipFile /HBpersistence/SWDL/Log/SubDirsIndex.txt.z 21093
skipFile /HBpersistence/SWDL/Log/SubDirsRestart.txt.z 21165
skipFile /HBpersistence/SWDL/Log/RepeatCo.unt.z 21239
skipFile /HBpersistence/SWDL/Log/CfgAck.z 21307
skipFile /HBpersistence/SWDL/Log/SvmOld.z 21370
skipFile /HBpersistence/SWDL/Log/SvmInfoIgnoreImages.txt 21846
skipFile /HBpersistence/SWDL/region.txt.z 21943
skipFile /HBpersistence/SWDL/MuRingType.txt 22005
skipFile /HBpersistence/SWDL/info/MuVariant.txt.z 22070
skipFile /HBpersistence/SWDL/info/MuHwIndex.txt.z 22139
skipFile /HBpersistence/SWDL/info/MuRegion.txt.z 22208
skipFile /HBpersistence/SWDL/info/IgnoreRegionVariant.txt.z 22276
skipFile /HBpersistence/SWDL/IT/hwIndex.txt 22356
skipFile /HBpersistence/SWDL/FileCopyInfo/AudiSupportedFscs.info 22412
skipFile /HBpersistence/SWDL/FileCopyInfo/MuTnrRef.info 22580
skipFile /HBpersistence/SWDL/FileCopyInfo/MUConsistency.info 22720
skipFile /HBpersistence/SWDL/FileCopyInfo/GEMMI.info 22883
skipFile /HBpersistence/SWDL/FileCopyInfo/sss.info 23001
skipFile /HBpersistence/SWDL/FileCopyInfo/MapStyles.info 24398
skipFile /HBpersistence/SWDL/FileCopyInfo/TMCConfig.info 25576
skipFile /HBpersistence/SWDL/FileCopyInfo/NaviPersistence.info 25778
skipFile /HBpersistence/SWDL/FileCopyInfo/AUDI_MMI3G_ECE.info 26037
skipFile /HBpersistence/SWDL/MainUnit-version2.txt 27660
skipFile /HBpersistence/SWDL/MainUnit-version2.txt.SWDL.version.txt 30451
skipFile /HBpersistence/SWDL/MainUnit-version2.txt.SWDL.compatibility.txt 30542
skipFile /HBpersistence/SWDL/update.txt.Abort.old 30632
skipFile /HBpersistence/SWDL/Emergency/FpgaOK 37409
skipFile /HBpersistence/FSC/cache/00040008.fsc 37728
skipFile /HBpersistence/FSC/cache/00040009.fsc 37786
skipFile /HBpersistence/FSC/Logs/Security_Exceptions.log 37844
skipFile /HBpersistence/FSC/00040009.fsc 44812
skipFile /HBpersistence/FSC/0004000A.fsc 45066
SWDL: Stopping EFS driver!
result of running command stop_efs_driver.sh is 0
SWDL: Starting EFS driver (automount)!
result of running command start_efs_driver.sh is 0
Set DisplayStatus to 6
/HBpersistence/SWDL is available!
/HBpersistence/SWDL/update.txt doesn't exist
Copy of /HBpersistence/SWDL/update.txt.backup to /HBpersistence/SWDL/update.txt failed
Don't use update.txt
SWDL: Mount from medium 3 (0)
OnOff: variant 9411
OnOff: DeviceName MU9411
Src: Medialauncher is running
Src: mount failed. Retry once in 1 s
Src: Medialauncher is running
Src: mount failed (medium unavailable 2)
SWDL: mount failed
SWDL: Mount from medium 4 (1)
Src: Medialauncher is running
Src: mount OK
SWDL: mount OK
SWDL: open metainfo /metainfo2.txt
SWDL: open finished (204016)
OnOff: FileAccess for continues!
OnOff: Current file access type: read
SWDL: read finished (204016, 0)
SWDL: parse metainfo
SWDL: use metainfo
Old image[0]: ipl 0, 0x0 0x40000
Old image[1]: fpga 1, 0x40000 0xc0000
Old image[2]: fpga-emg 2, 0x100000 0xc0000
Old image[3]: ifs-emg 5, 0x1c0000 0x4982dc
New image[0]: ipl 0, 0x0 0xf720
New image[1]: fpga 1, 0x40000 0xb6410
New image[2]: fpga-emg 2, 0x100000 0xb63f0
New image[3]: ifs-emg 5, 0x1c0000 0x4aae6c
New image[4]: ifs-root 3, 0x680000 0x29b88cc
New image[5]: efs-extended 6, 0x3100000 0xc00000
New image[6]: efs-system 6, 0x3d00000 0x2500000
New image[7]: efs-persist 6, 0x6200000 0x1d00000
eraseOrphanedImageHeaders: Check image 0/4
eraseOrphanedImageHeaders: Check image 1/4
eraseOrphanedImageHeaders: Check image 2/4
eraseOrphanedImageHeaders: Check image 3/4
Erased orphaned image headers
Updated FPGA info flag (II)
SWDL: Stopping EFS driver!
result of running command stop_efs_driver.sh is 0
SWDL: Starting EFS driver (no automount)!
result of running command start_efs_driver.sh -a is 0
OnOff: Max images 8
OnOff: image release version 3092
SWDL: open file /MU9411/ifs-root/41/default/ifs-root.ifs
OnOff: image release version 2098
OnOff: image release version 24
OnOff: image release version 2125
dev_fd == 12
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0x680000
limit: 0x40000
OnOff: image name ifs-root
OnOff: image index 4
SWDL: open finished (43738260)
OnOff: phase Erase
OnOff: Progress 000
SWDL: read finished (524288, 0)
SWDL: read finished (524288, 524288)
SWDL: read finished (524288, 1048576)
SWDL: read finished (524288, 1572864)
devctl(12,-2146694912,xx,12,0) returned 0dev_fd == 12
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0x6c0000
limit: 0x40000
SWDL: read finished (524288, 2097152)
SWDL: read finished (524288, 2621440)
SWDL: read finished (524288, 3145728)
SWDL: read finished (524288, 3670016)
SWDL: read finished (524288, 4194304)
SWDL: read finished (524288, 4718592)
SWDL: read finished (524288, 5242880)
devctl(12,-2146694912,xx,12,0) returned 0SWDL: read finished (524288, 5767168)
OnOff: Progress 001
dev_fd == 12
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0x700000
limit: 0x40000
SWDL: read finished (524288, 6291456)
SWDL: read finished (524288, 6815744)
SWDL: read finished (524288, 7340032)
SWDL: read finished (524288, 7864320)
SWDL: read finished (524288, 8388608)
SWDL: read finished (524288, 8912896)
SWDL: read finished (524288, 9437184)
SWDL: read finished (524288, 9961472)
devctl(12,-2146694912,xx,12,0) returned 0dev_fd == 12
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0x740000
limit: 0x40000
SWDL: read finished (524288, 10485760)
SWDL: read finished (524288, 11010048)
SWDL: read finished (524288, 11534336)
SWDL: read finished (524288, 12058624)
SWDL: read finished (524288, 12582912)
SWDL: read finished (524288, 13107200)
SWDL: read finished (524288, 13631488)
devctl(12,-2146694912,xx,12,0) returned 0SWDL: read finished (524288, 14155776)
OnOff: Progress 002
dev_fd == 12
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0x780000
limit: 0x40000
SWDL: read finished (524288, 14680064)
SWDL: read finished (524288, 15204352)
SWDL: read finished (524288, 15728640)
SWDL: read finished (524288, 16252928)
SWDL: read finished (524288, 16777216)
SWDL: read finished (524288, 17301504)
SWDL: read finished (524288, 17825792)
devctl(12,-2146694912,xx,12,0) returned 0dev_fd == 12
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0x7c0000
limit: 0x40000
SWDL: read finished (524288, 18350080)
SWDL: read finished (524288, 18874368)
SWDL: read finished (524288, 19398656)
SWDL: read finished (524288, 19922944)
SWDL: read finished (524288, 20447232)
SWDL: read finished (524288, 20971520)
SWDL: read finished (524288, 21495808)
SWDL: read finished (524288, 22020096)

kaon

09.01.2016, 12:49

devctl(12,-2146694912,xx,12,0) returned 0OnOff: Progress 003
dev_fd == 12
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0x800000
limit: 0x40000
SWDL: read finished (524288, 22544384)
SWDL: read finished (524288, 23068672)
SWDL: read finished (524288, 23592960)
SWDL: read finished (524288, 24117248)
SWDL: read finished (524288, 24641536)
SWDL: read finished (524288, 25165824)
SWDL: read finished (524288, 25690112)
SWDL: read finished (524288, 26214400)
devctl(12,-2146694912,xx,12,0) returned 0SWDL: read finished (524288, 26738688)
OnOff: Progress 004
dev_fd == 12
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0x840000
limit: 0x40000
SWDL: read finished (524288, 27262976)
SWDL: read finished (524288, 27787264)
SWDL: read finished (524288, 28311552)
SWDL: read finished (524288, 28835840)
SWDL: read finished (524288, 29360128)
SWDL: read finished (524288, 29884416)
SWDL: read finished (524288, 30408704)
SWDL: read finished (524288, 30932992)
devctl(12,-2146694912,xx,12,0) returned 0dev_fd == 12
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0x880000
limit: 0x40000
SWDL: read finished (524288, 31457280)
SWDL: read finished (524288, 31981568)
SWDL: read finished (524288, 32505856)
SWDL: read finished (524288, 33030144)
SWDL: read finished (524288, 33554432)
SWDL: read finished (524288, 34078720)
SWDL: read finished (524288, 34603008)
SWDL: read finished (524288, 35127296)
devctl(12,-2146694912,xx,12,0) returned 0OnOff: Progress 005
dev_fd == 12
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0x8c0000
limit: 0x40000
SWDL: read finished (524288, 35651584)
SWDL: read finished (524288, 36175872)
SWDL: read finished (524288, 36700160)
SWDL: read finished (524288, 37224448)
SWDL: read finished (524288, 37748736)
SWDL: read finished (524288, 38273024)
SWDL: read finished (524288, 38797312)
SWDL: read finished (524288, 39321600)
devctl(12,-2146694912,xx,12,0) returned 0SWDL: read finished (524288, 39845888)
dev_fd == 12
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0x900000
limit: 0x40000
SWDL: read finished (524288, 40370176)
SWDL: read finished (524288, 40894464)
SWDL: read finished (524288, 41418752)
SWDL: read finished (524288, 41943040)
SWDL: read finished (524288, 42467328)
SWDL: read finished (524288, 42991616)
SWDL: read finished (222356, 43515904)
devctl(12,-2146694912,xx,12,0) returned 0OnOff: Progress 006
dev_fd == 11
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0x940000
limit: 0x40000
devctl(11,-2146694912,xx,12,0) returned 0OnOff: Progress 007
dev_fd == 11
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0x980000
limit: 0x40000
devctl(11,-2146694912,xx,12,0) returned 0dev_fd == 11
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0x9c0000
limit: 0x40000
devctl(11,-2146694912,xx,12,0) returned 0OnOff: Progress 008
dev_fd == 11
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0xa00000
limit: 0x40000
devctl(11,-2146694912,xx,12,0) returned 0dev_fd == 11
devctl returned 0
arrayinfo.unit_size 262144
calling devctl with erase struct:
status: 0
offset: 0xa40000
limit: 0x40000

и так далее.
что не так я делаю?

kaon

09.01.2016, 15:26

вопрос закрыт, все само собой разрешилось и ММИ ожила=)

zerbino

09.01.2016, 17:55

вопрос закрыт, все само собой разрешилось и ММИ ожила=)

Содержательно, конечно) Вы уж простите, но "само собой" даже голуби не какают:D

v8900

09.01.2016, 20:14

доброго времени , подскажите пожалуйста у кого есть возможность сделать образ диска hdd с mmi3g hi , у меня умер винт , хочу поэкспериментировать с ssd диском

kaon

09.01.2016, 20:23

собственно в выложенном мною логе никаких ошибок и нет, идет стандартное восстановление головы.
По невнимательности воткнул кабель монитора в AMI разъем, соответственно монитор ничего не отображает, кроме черного экрана....а восстановление идет=))))

Crash-100

09.01.2016, 20:25

доброго времени , подскажите пожалуйста у кого есть возможность сделать образ диска hdd с mmi3g hi , у меня умер винт , хочу поэкспериментировать с ssd диском
а есть SSD с IDE ?

v8900

09.01.2016, 20:27

хочу попробовать через переходник ide - sata

kaon

09.01.2016, 20:35

Краш, я кстати узнал алгоритм создания токенов у австралийца.

zerbino

09.01.2016, 20:53

Краш, я кстати узнал алгоритм создания токенов у австралийца.
Этот алгоритм виден, если скрипт раскодировать)

v8900 на сколько мне не изменяет память, эксперименты на том и закончатся. Т.е. даже через переходники SSD to IDE, и сами переходники и сами жесткие диски, почему-то не отдают себя SLAVE контроллеру на блоке. Я полагаю, что таки этому можно уломать блок, но мне лично лень копаться. Легче купить обычный хард ноутбучный за 25 баксов у китайцев и поменять его и всё будет работать.
Но вы несомненно, если допилите это, делитесь со всеми, а то ж век не долог хардов с блинами, их уже и не найти почти в продаже, в отличие от SSD IDE или переходников IDE <= NGFF m.2 SSD

v8900

09.01.2016, 21:05

так что насчет образа ?

zerbino

09.01.2016, 21:10

kaon
По невнимательности воткнул кабель монитора в AMI разъем, соответственно монитор ничего не отображает, кроме черного экрана....а восстановление идет=))))
А я то думаю в чем сакральный смысл автоматической перезаписи образов :D

v8900
У меня нет, у меня RNS850. По сути одно и то же, не все же не то.

Crash-100

09.01.2016, 22:49

Этот алгоритм виден, если скрипт раскодировать)

v8900 на сколько мне не изменяет память, эксперименты на том и закончатся. Т.е. даже через переходники SSD to IDE, и сами переходники и сами жесткие диски, почему-то не отдают себя SLAVE контроллеру на блоке. Я полагаю, что таки этому можно уломать блок, но мне лично лень копаться. Легче купить обычный хард ноутбучный за 25 баксов у китайцев и поменять его и всё будет работать.
Но вы несомненно, если допилите это, делитесь со всеми, а то ж век не долог хардов с блинами, их уже и не найти почти в продаже, в отличие от SSD IDE или переходников IDE <= NGFF m.2 SSD
подтверждаю, просто переходник ничего не дась, винт не будет определен системой, IDE 160 GB запихнул в 3GP - работает, образ не проблема могу сделать, но он весит очень много.

v8900

09.01.2016, 23:01

знаю что объем большой, поэтому ненавязчиво прошу, вариант с ssd я понял еще ни у кого не заработал, а вариант с sdxc через cf - ide

sergeynik

09.01.2016, 23:06

посекторная копия всеравно не катит тк разное количество секторов на дорожку. если голова видит диск как девайс то встроенный фдиск все может разбить

v8900

09.01.2016, 23:12

Hi All,

I have now performed this "HDD Upgrade" procedure MMI 3G Plus units several times in the last few months and it works like a charm:
1. Download macrium reflect free edition.
2. Remove the original Toshiba HDD from the MMI unit.
3. Connect the drive into IDE<->USB connector
4. Clone the drive into an image using macrium (Forensic method)
5. Disconnect the original drive and insert a bigger drive (you have 3 choices: Normal IDE HDD (not recommended) / SDXC SD card in IDE Sleeve (Good) / IDE SSD (Best))
6. Restore the image into the drive, one partition at the time.
7. On the second partition re-size the destination partition to expand to the remainder of 'new addition' space
8. Restore the rest of partitions.
9. Connect the new drive into MMI unit
10. Jukebox is now not working, so go to Setup -> Settings of MMI -> Reset and Select Jukebox.
11. Reboot MMI and repeat step number 10 again.
12. Final reboot.
13. Jukebox is now resized, the rest of the systems are all working ok.

I hope this helps!

Regards,
Keldo Gliana

а у этого товарища работает

sergeynik

09.01.2016, 23:15

я пробовал sata не заводятся

v8900

09.01.2016, 23:18

всмысле сата диск через переходник ?

zerbino

09.01.2016, 23:22

посекторная копия всеравно не катит тк разное количество секторов на дорожку. если голова видит диск как девайс то встроенный фдиск все может разбить
Как-то оно "само" что-то при замене диска на бОльший не разбивало и не форматило ничего.. Причем что интересно, те диски, которые "не виделись" в обычной загрузке, были видны при Emg загрузке. Странно. Это на RNS850 было.
Благодаря Uknik удалось гибридным способом переразбить разделы. Но файлы с QNX виртуалке мне было лень. Поэтому я пользуюсь способом таким. Разбиваю по шаблону диск посекторно точ в точь как в оригинале, кроме media раздела. После этого клонирую разделы все, кроме MEDIA с помощью rmprepusb. Форматирую в виртуалке QNX через "mkqnx6fs -q /dev/hd0t78", ну а дальше всё ок.
Кстати да,

sergeynik

09.01.2016, 23:22

да чип переходника писал тут кадато

sergeynik

09.01.2016, 23:24

само и не должно. втыкаешь винт в мми и в консоле fdisk

zerbino

09.01.2016, 23:25

Вы сразу с даташитом на SPIF223A разберитесь тогда)

olegdick

13.01.2016, 21:40

С наступающим Старым Новым годом...
После не удачной активации карт. экран чёрный и кнопки не светяться
ввёл команду
boot 1c0000
вот итог
###########################################

starting image @801c0000 ...
Startup: PL_qnx_startup-sh7785_08362A, built 2008/09/02_07-53-12_UTC
RAM : 256 MB @0x08000000
FLASH: 128 MB @0x00000000
System page at phys:0800a000 user:0800a000 kern:8800a000
Starting next program at v88046840
------------------------------------------------------
Welcome to QNX 6.3.2 (RL_qnx_os_632_PSP3_08124A) MMI3G Audi EMERGENCY SETUP 9308 D1 09431A
starting pci driver
*** init FPGA registers ***
starting dev-ipc for IOC
initialize IPC Driver
starting network driver
starting atapi driver - setup device /dev/cam0
starting devc-pty
Path=0 - XILINX MMI3G_8
target=0 lun=0 CD-ROM(5) - FJ-TEN DVD-ROM DV-05FT2 Rev: 1B20
Path=1 - XILINX MMI3G_8
target=1 lun=0 Direct-Access(0) - TOSHIBA MK4050GA Rev: TG10
starting flash driver
starting SDCard driver
Unable to access "/dev/io-net/en5" (2)
starting with no network driver
================================================== =========
Emergency IFS is started. Emergency app tries to restore
the application.
================================================== =========
49169 running /usr/bin/devg-NVTIRM
DMA is Disabled
dma disabled, interrupt thread priority = 100
49171 running /sbin/io-media-nvidia
49172 running /usr/sbin/io-display
49173 running /usr/apps/MMI3GEmergencyApp
================================================== =========
Emergency shell started, fix your system and restart again
================================================== =========
discplayer_init: IN
nvidia_render_manager_init: IN
INvmRenderManager::GetNvmRenderManager (&pRenderManager);
er = pRenderManager->Init(oConfig);
# App FPGA valid 1
Emergency FPGA valid 1
Disabling IOC watchdog
EmergencyApp-MMI3G: version 22.30.1642, date of build 14.10.2009
pRenderManager->Open()
nvidia_render_manager_init: OUT
discplayer_init: OUT
discplayer_init
discplayer_init: IN
nvidia_render_manager_init: IN
nvidia_render_manager_init: OUT
discplayer_init: OUT
dvdtrackplayer_init
discplayer_init: IN
nvidia_render_manager_init: IN
nvidia_render_manager_init: OUT
discplayer_init: OUT
dvdnavigator_init
created navigator control point with 8249288
mixer_init: IN
mixer_init: OUT
NvTRACELEVEL set to 3 (Level Info)
nVAudio_init: IN
nvidia_render_manager_init();
nvidia_render_manager_init: IN
nvidia_render_manager_init: OUT
nVAudio_init: OUT
installing audio decoders
installing video decoders
nVAudio_init: IN
nvidia_render_manager_init();
nvidia_render_manager_init: IN
nvidia_render_manager_init: OUT
nVAudio_init: OUT
OnIpcGetCaptureUnitSourceCount
Number of displays: 6
Number of layers: 9
Graphics init was successfull: DisplaySize is 800x 480
The FPGA for the application is valid!
Emergency application will do nothing!
(devf t1::f3s_recover_boot:141) fs1p1 boot P[EF] U: 58
result of running command start_efs_driver.sh is 0
(devf t1::f3s_recover_boot:141) fs1p2 boot P[138] U: 50
(devf t1::f3s_recover_boot:141) fs1p3 boot P[1E5] U: 74
Wait for HBpersistence...
HBpersistence is available!
************************************************** *********
** DeveloperMode is off!!!! **
** The system will shutdown soon! **
** DO NOT FLASH WITH SCRIPTS IN THIS MODE!!! **
************************************************** *********
** You can enable DeveloperMode like this: **
** echo dummy > /HBpersistence/DeveloperMode **
************************************************** *********
Set DisplayStatus to 2
OnOff: process IPC event HWsample 209 HWvariant 7 FinalShutdown 0
OnOff: process IPC event HWsample 209 HWvariant 7 FinalShutdown 0
OnOff: process IPC event HWsample 209 HWvariant 7 FinalShutdown 0
OnOff: process IPC event HWsample 209 HWvariant 7 FinalShutdown 0
OnOff: process IPC event HWsample 209 HWvariant 7 FinalShutdown 0
OnOff: process IPC event HWsample 209 HWvariant 7 FinalShutdown 0
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Enabling IOC watchdog
Initiate shutdown (after BEM timeout)...
OnOff: process IPC event HWsample 209 HWvariant 7 FinalShutdown 0
OnOff: process IPC event HWsample 209 HWvariant 7 FinalShutdown 0
OnOff: process IPC event HWsample 209 HWvariant 7 FinalShutdown 0

что это значит. Помогите пожалуйста.

olegdick

13.01.2016, 21:50

Было красное меню. через 60 секунд мми выключилось.
но экран всёравно чёрный и кнопки не светяться.
подскажите пожалуйста что надо делать.

sergeynik

13.01.2016, 22:55

онож просит для начала
echo dummy > /HBpersistence/DeveloperMode
чтоб не перезагражалось

olegdick

14.01.2016, 07:30

спосибо. после работы попробую.
писать полностью?
echo dummy > /HBpersistence/DeveloperMode

sergeynik

14.01.2016, 10:25

создай пустой файл "DeveloperMode" в папке /HBpersistence

dim250568

14.01.2016, 19:52

Привет Всем подскажите какая папка и какой файл отвечает за клавиатуру в прошивки 900 на 4G

николай11

14.01.2016, 20:58

всем привет прошу помочь с rns 850 не допесал до конца команду flashit -a 40000 -e 1000 а написал flashit -a 4000 -e 1000 и перестала голова выходить через терминал,за ранние спасибо.

Crash-100

14.01.2016, 21:04

Теперь придется еще разобраЦЦо с JTAG

николай11

14.01.2016, 21:06

а это что такое JTAG

Crash-100

14.01.2016, 21:15

Николай, Вы откуда такой неудачливый ?

николай11

14.01.2016, 21:24

из москвы

николай11

14.01.2016, 21:25

как я понимаю очень печально с rns

Crash-100

14.01.2016, 21:26

Ваш первый опыт был неудачен, без Jtag голову не поднять, на форуме есть информация по подключению, но это кусок работы, найдите кого-нибудь из Москвы, кто сможет поднять ее.

николай11

14.01.2016, 21:28

я припоялся к rx tx gnd

николай11

14.01.2016, 21:30

а что именно надо зделать чтобы поднять её

Crash-100

14.01.2016, 21:33

Вы стерли кусок IPL 63kB которые трогать нельзя !

николай11

14.01.2016, 21:35

а где он находится

Crash-100

14.01.2016, 21:37

а где он находится

Это абсурд !!!!!

николай11

14.01.2016, 21:41

а вы знайте людеи из москвы кто может мне помоч

slav

20.01.2016, 01:38

Я так подозреваю, один в Киеве, другой в Минске ))

zerbino

20.01.2016, 01:43

Третий в Москве, но его я рекомендовать не буду)

webzter

06.02.2016, 18:46

После обновление прошивки с 475 на 612 пропускала голосовые файлы после перещагрузки вылез зеленый экран, далее файлы читаются до середины и выдается ошибкаFile Error на красном фоне. Попробовал все прошивки везде CRC Error кроме 612 версии с которой обновлялся.

Что делать, это можно восстановить ?

bajusz66

10.02.2016, 14:11

алло
Я из Венгрии и купил новый блок A8 4H0035670N плохо, но компьютер видитнеизвестные символы .Не хороший кабель?
Спасибо за помощь
http://kepfeltoltes.hu/160210/12674808_10203948589473761_1680054909_o_www.kepfel toltes.hu_.jpg

Vlasoff

15.02.2016, 22:46

алло
Я изВенгриии купилновый блокA84H0035670Nплохо,но компьютервидитнеизвестные символы.Нехороший кабель?
Спасибо за помощь
http://kepfeltoltes.hu/160210/12674808_10203948589473761_1680054909_o_www.kepfel toltes.hu_.jpg

алло алло как слышно :D

zerbino

15.02.2016, 23:10

Первый, Первый, я Второй, как слышите?! Приём!

Victor_ua

18.02.2016, 20:22

алло
Я изВенгриии купилновый блокA84H0035670Nплохо,но компьютервидитнеизвестные символы.Нехороший кабель?
Спасибо за помощь
http://kepfeltoltes.hu/160210/12674808_10203948589473761_1680054909_o_www.kepfel toltes.hu_.jpg

Hello. Adjon kapcsolatok, én szombaton Budapesten, és segíthet

zerbino

18.02.2016, 20:36

Ich bin ingenieur von beruf.:D

К нему адаптер (http://www.ebay.com/itm/161970857936) едет, уже по Венгрии катается. Челу лень посмотреть параметры порта и запаяться какчественно.. О чем речь..
Ниче, скоро подключится по готовому по USB и сам всё починит.

bajusz66

18.02.2016, 23:30

Ha holnap nincs itt a csatlakozó amit zerbinotól vettem akkor megyek.150km nekem budapest.
Köszönöm a segítséget :D

bajusz66

20.02.2016, 09:43

Hello. Adjon kapcsolatok, én szombaton Budapesten, és segíthet
Hello
Küldtem kapcsolatot.
Megjött az adapter(Köszönöm zerbino) de azzal sem boldogulok.

Crash-100

21.02.2016, 19:40

Nos, akkor írd, hogy miért ez az egész?

bajusz66

21.02.2016, 19:59

Nos, akkor írd, hogy miért ez az egész?
Vettem egy 3GP A8 4H0035670N unitot az autómba.Mikor beletettem nem indult,fekete képernyő,semmi reakció.Én azt gondoltam hátha megbirom javítani, mert olvastam hogy helyre lehet hozni USB uart ttl adapterrel.Ma volt itt az egyik ismerős rossz aktivátort használt és leszerelt a navi.Azt a navit megbirtam csinálni az adapterrel amit vettem zerbinotól.De a sajátommal nem boldogulok.Gondoltam itt kaphatok egy kis segítséget.Lényegében ennyi.
:D
UI:
Bocs a zavarásért
:D

Crash-100

21.02.2016, 20:02

írni angolul

zerbino

21.02.2016, 20:04

而我们不能做一个口头的垃圾在这里?

Crash-100

21.02.2016, 20:05

このハンガリー

zerbino

21.02.2016, 20:08

יא, אַפֿילו ישראל.

Link

21.02.2016, 21:59

Tie vi havas nenion komunan

zerbino

21.02.2016, 22:02

STOP damage my head unit!:cf:

bajusz66

21.02.2016, 22:15

STOP damage my head unit!:cf:
:stupid:

audijiJQ

22.02.2016, 04:23

楼上的，你们是在搞笑吗？:D

parsec82

24.02.2016, 16:51

i have tried to recovery a unit from failed update.
the unit at this moment start up correctly.
but if i try to install the maps (2015) all the update go failed.

during the boot i have see this strange error:

[WRN]@35874 (122905.9): devctl '0X4090055C' <DCMD_HB_HDDMGR_GETDRIVEIDENTITY> call failed(errCode = 5 <Input/output error>)
[WRN]@35918 (122905.9): devctl '0X4090055C' <DCMD_HB_HDDMGR_GETDRIVEIDENTITY> call failed(errCode = 5 <Input/output error>)
[WRN]@35924 (122905.9): devctl '0X4090055C' <DCMD_HB_HDDMGR_GETDRIVEIDENTITY> call failed(errCode = 5 <Input/output error>)
[WRN]@35938 (122905.9): Try to fix connection...
[WRN]@35946 (122905.9): devctl '0X4090055C' <DCMD_HB_HDDMGR_GETDRIVEIDENTITY> call failed(errCode = 5 <Input/output error>)
[WRN]@35955 (122905.9): devctl '0X4090055C' <DCMD_HB_HDDMGR_GETDRIVEIDENTITY> call failed(errCode = 5 <Input/output error>)
[WRN]@35963 (122905.9): devctl '0X4090055C' <DCMD_HB_HDDMGR_GETDRIVEIDENTITY> call failed(errCode = 5 <Input/output error>)
[WRN]@35979 (122905.9): devctl '0X4090055C' <DCMD_HB_HDDMGR_GETDRIVEIDENTITY> call failed(errCode = 5 <Input/output error>)
[WRN]@35983 (122905.9): devctl '0X4090055C' <DCMD_HB_HDDMGR_GETDRIVEIDENTITY> call failed(errCode = 5 <Input/output error>)
[WRN]@36030 (122905.9): devctl '0X4090055C' <DCMD_HB_HDDMGR_GETDRIVEIDENTITY> call failed(errCode = 5 <Input/output error>)
[WRN]@36037 (122905.9): Try to fix connection...
[WRN]@36043 (122905.9): devctl '0X4090055C' <DCMD_HB_HDDMGR_GETDRIVEIDENTITY> call failed(errCode = 5 <Input/output error>)
[WRN]@36079 (122905.9): devctl '0X4090055C' <DCMD_HB_HDDMGR_GETDRIVEIDENTITY> call failed(errCode = 5 <Input/output error>)
[WRN]@36116 (122905.9): devctl '0X4090055C' <DCMD_HB_HDDMGR_GETDRIVEIDENTITY> call failed(errCode = 5 <Input/output error>)
[NATIVE-RESMGR-PROXY]: No valid GEMMI installation found - stop
[t(p) proc/boot/procnto-instr 1 1 0 8807a22e]
[WRN]@38005 (122905.9): devctl '0X4090055C' <DCMD_HB_HDDMGR_GETDRIVEIDENTITY> call failed(errCode = 5 <Input/output error>)
[WRN]@38058 (122905.9): devctl '0X4090055C' <DCMD_HB_HDDMGR_GETDRIVEIDENTITY> call failed(errCode = 5 <Input/output error>)
[WRN]@38107 (122905.9): devctl '0X4090055C' <DCMD_HB_HDDMGR_GETDRIVEIDENTITY> call failed(errCode = 5 <Input/output error>)
[WRN]@38146 (122905.9): Try to fix connection...
[WRN]@38206 (122905.9): devctl '0X4090055C' <DCMD_HB_HDDMGR_GETDRIVEIDENTITY> call failed(errCode = 5 <Input/output error>)
[WRN]@38261 (122905.9): devctl '0X4090055C' <DCMD_HB_HDDMGR_GETDRIVEIDENTITY> call failed(errCode = 5 <Input/output error>)
[WRN]@38297 (122905.9): devctl '0X4090055C' <DCMD_HB_HDDMGR_GETDRIVEIDENTITY> call failed(errCode = 5 <Input/output error>)

i think are a problem with the Hard disk but i'm unable to recovery this problem :-(
anyone have solved a similar problem?

parsec82

24.02.2016, 18:25

Problem solved... Hard disk are not working... i have changed the hard disk and all work perfectly

i have tried to recovery a unit from failed update.
the unit at this moment start up correctly.
but if i try to install the maps (2015) all the update go failed.

during the boot i have see this strange error:

[WRN]@35874 (122905.9): devctl '0X4090055C' <DCMD_HB_HDDMGR_GETDRIVEIDENTITY> call failed(errCode = 5 <Input/output error>)
[WRN]@35918 (122905.9): devctl '0X4090055C' <DCMD_HB_HDDMGR_GETDRIVEIDENTITY> call failed(errCode = 5 <Input/output error>)
[WRN]@35924 (122905.9): devctl '0X4090055C' <DCMD_HB_HDDMGR_GETDRIVEIDENTITY> call failed(errCode = 5 <Input/output error>)
[WRN]@35938 (122905.9): Try to fix connection...
[WRN]@35946 (122905.9): devctl '0X4090055C' <DCMD_HB_HDDMGR_GETDRIVEIDENTITY> call failed(errCode = 5 <Input/output error>)
[WRN]@35955 (122905.9): devctl '0X4090055C' <DCMD_HB_HDDMGR_GETDRIVEIDENTITY> call failed(errCode = 5 <Input/output error>)
[WRN]@35963 (122905.9): devctl '0X4090055C' <DCMD_HB_HDDMGR_GETDRIVEIDENTITY> call failed(errCode = 5 <Input/output error>)
[WRN]@35979 (122905.9): devctl '0X4090055C' <DCMD_HB_HDDMGR_GETDRIVEIDENTITY> call failed(errCode = 5 <Input/output error>)
[WRN]@35983 (122905.9): devctl '0X4090055C' <DCMD_HB_HDDMGR_GETDRIVEIDENTITY> call failed(errCode = 5 <Input/output error>)
[WRN]@36030 (122905.9): devctl '0X4090055C' <DCMD_HB_HDDMGR_GETDRIVEIDENTITY> call failed(errCode = 5 <Input/output error>)
[WRN]@36037 (122905.9): Try to fix connection...
[WRN]@36043 (122905.9): devctl '0X4090055C' <DCMD_HB_HDDMGR_GETDRIVEIDENTITY> call failed(errCode = 5 <Input/output error>)
[WRN]@36079 (122905.9): devctl '0X4090055C' <DCMD_HB_HDDMGR_GETDRIVEIDENTITY> call failed(errCode = 5 <Input/output error>)
[WRN]@36116 (122905.9): devctl '0X4090055C' <DCMD_HB_HDDMGR_GETDRIVEIDENTITY> call failed(errCode = 5 <Input/output error>)
[NATIVE-RESMGR-PROXY]: No valid GEMMI installation found - stop
[t(p) proc/boot/procnto-instr 1 1 0 8807a22e]
[WRN]@38005 (122905.9): devctl '0X4090055C' <DCMD_HB_HDDMGR_GETDRIVEIDENTITY> call failed(errCode = 5 <Input/output error>)
[WRN]@38058 (122905.9): devctl '0X4090055C' <DCMD_HB_HDDMGR_GETDRIVEIDENTITY> call failed(errCode = 5 <Input/output error>)
[WRN]@38107 (122905.9): devctl '0X4090055C' <DCMD_HB_HDDMGR_GETDRIVEIDENTITY> call failed(errCode = 5 <Input/output error>)
[WRN]@38146 (122905.9): Try to fix connection...
[WRN]@38206 (122905.9): devctl '0X4090055C' <DCMD_HB_HDDMGR_GETDRIVEIDENTITY> call failed(errCode = 5 <Input/output error>)
[WRN]@38261 (122905.9): devctl '0X4090055C' <DCMD_HB_HDDMGR_GETDRIVEIDENTITY> call failed(errCode = 5 <Input/output error>)
[WRN]@38297 (122905.9): devctl '0X4090055C' <DCMD_HB_HDDMGR_GETDRIVEIDENTITY> call failed(errCode = 5 <Input/output error>)

i think are a problem with the Hard disk but i'm unable to recovery this problem :-(
anyone have solved a similar problem?

ZippeR

25.02.2016, 18:24

Господа а здесь только MMi3G обсуждается? может кто знает на какие пины вешаться чтобы зайти терминалов в Discover Pro/Columbus на mqb которые? Спасибо.

parsec82

29.02.2016, 15:52

i have another question.
i have unit (mmi 3gp 8R1 035 666) that have the EFS-Persist damaged, i have another unit for extract the EFS-Persist but i don't find the mothod to extract that data...
There is a script for backup this partition on a BIN for manually flashit through terminal?

Crash-100

29.02.2016, 16:16

what is problem you have with EFS-Persist ?

Crash-100

29.02.2016, 16:54

what is problem you have with EFS-Persist ?

parsec82

29.02.2016, 17:12

when i have recovered the unit i have see the error regards the efs-persist corrupted. and the unit remain locked when i start.
through com connection i read this:

amd_poll: 186 DQ7 polling Timeout
(devf t2::f3s_aCFI_v2write:250) over poll waiting for write completion at 3fa81940, size 12
(devf t2::f3s_ext_write:195) fs0p3 bad H[19] P[1E6] # 00000C # 00000000
(devf t2::f3s_file_create:110) fs0p3 error -1
[t(p) usr/sbin/devf-generic 12290 2 11 806337e]
[t(c) usr/bin/PSSBSSProcess 213047 1 11 7033519a]
amd_poll: 186 DQ7 polling Timeout
(devf t2::f3s_aCFI_v2write:250) over poll waiting for write completion at 3fa8194c, size 12
(devf t2::f3s_ext_write:195) fs0p3 bad H[1A] P[1E6] # 00000C # 00000000
(devf t2::f3s_file_create:110) fs0p3 error -1
amd_poll: 186 DQ7 polling Timeout
(devf t2::f3s_aCFI_v2write:250) over poll waiting for write completion at 3fa81958, size 12
(devf t2::f3s_ext_write:195) fs0p3 bad H[1B] P[1E6] # 00000C # 00000000
(devf t2::f3s_file_create:110) fs0p3 error -1
amd_poll: 186 DQ7 polling Timeout
(devf t2::f3s_aCFI_v2write:250) over poll waiting for write completion at 3fa81964, size 12
(devf t2::f3s_ext_write:195) fs0p3 bad H[1C] P[1E6] # 00000C # 00000000
(devf t2::f3s_file_create:110) fs0p3 error -1
amd_poll: 186 DQ7 polling Timeout
(devf t2::f3s_aCFI_v2write:250) over poll waiting for write completion at 3fa81970, size 12
(devf t2::f3s_ext_write:195) fs0p3 bad H[1D] P[1E6] # 00000C # 00000000
(devf t2::f3s_file_create:110) fs0p3 error -1
amd_poll: 186 DQ7 polling Timeout
(devf t2::f3s_aCFI_v2write:250) over poll waiting for write completion at 3fa8197c, size 12
(devf t2::f3s_ext_write:195) fs0p3 bad H[1E] P[1E6] # 00000C # 00000000
(devf t2::f3s_file_create:110) fs0p3 error -1
[t(p) usr/sbin/devf-generic 12290 2 11 8066bc8]
[t(c) usr/bin/PSSBSSProcess 213047 1 11 7033519a]
amd_poll: 186 DQ7 polling Timeout
(devf t2::f3s_aCFI_v2write:250) over poll waiting for write completion at 3fa81988, size 12
(devf t2::f3s_ext_write:195) fs0p3 bad H[1F] P[1E6] # 00000C # 00000000
(devf t2::f3s_file_create:110) fs0p3 error -1
amd_poll: 186 DQ7 polling Timeout
(devf t2::f3s_aCFI_v2write:250) over poll waiting for write completion at 3fa81994, size 12
(devf t2::f3s_ext_write:195) fs0p3 bad H[20] P[1E6] # 00000C # 00000000
(devf t2::f3s_file_create:110) fs0p3 error -1
amd_poll: 186 DQ7 polling Timeout
(devf t2::f3s_aCFI_v2write:250) over poll waiting for write completion at 3fa819a0, size 12
(devf t2::f3s_ext_write:195) fs0p3 bad H[21] P[1E6] # 00000C # 00000000
(devf t2::f3s_file_create:110) fs0p3 error -1
amd_poll: 186 DQ7 polling Timeout
(devf t2::f3s_aCFI_v2write:250) over poll waiting for write completion at 3fa819ac, size 12
(devf t2::f3s_ext_write:195) fs0p3 bad H[22] P[1E6] # 00000C # 00000000
(devf t2::f3s_file_create:110) fs0p3 error -1
amd_poll: 186 DQ7 polling Timeout
(devf t2::f3s_aCFI_v2write:250) over poll waiting for write completion at 3fa819b8, size 12
(devf t2::f3s_ext_write:195) fs0p3 bad H[23] P[1E6] # 00000C # 00000000
(devf t2::f3s_file_create:110) fs0p3 error -1
amd_poll: 186 DQ7 polling Timeout
(devf t2::f3s_aCFI_v2write:250) over poll waiting for write completion at 3fa819c4, size 12
(devf t2::f3s_ext_write:195) fs0p3 bad H[24] P[1E6] # 00000C # 00000000
(devf t2::f3s_file_create:110) fs0p3 error -1
[t(p) usr/sbin/devf-generic 12290 2 11 8066bc8]
[t(c) usr/bin/PSSBSSProcess 213047 1 11 7033519a]
amd_poll: 186 DQ7 polling Timeout
(devf t2::f3s_aCFI_v2write:250) over poll waiting for write completion at 3fa819d0, size 12
(devf t2::f3s_ext_write:195) fs0p3 bad H[25] P[1E6] # 00000C # 00000000
(devf t2::f3s_file_create:110) fs0p3 error -1
amd_poll: 186 DQ7 polling Timeout
(devf t2::f3s_aCFI_v2write:250) over poll waiting for write completion at 3fa819dc, size 12
(devf t2::f3s_ext_write:195) fs0p3 bad H[26] P[1E6] # 00000C # 00000000
(devf t2::f3s_file_create:110) fs0p3 error -1
amd_poll: 186 DQ7 polling Timeout
(devf t2::f3s_aCFI_v2write:250) over poll waiting for write completion at 3fa819e8, size 12
(devf t2::f3s_ext_write:195) fs0p3 bad H[27] P[1E6] # 00000C # 00000000
(devf t2::f3s_file_create:110) fs0p3 error -1
amd_poll: 186 DQ7 polling Timeout
(devf t2::f3s_aCFI_v2write:250) over poll waiting for write completion at 3fa819f4, size 12
(devf t2::f3s_ext_write:195) fs0p3 bad H[28] P[1E6] # 00000C # 00000000
(devf t2::f3s_file_create:110) fs0p3 error -1
amd_poll: 186 DQ7 polling Timeout
(devf t2::f3s_aCFI_v2write:250) over poll waiting for write completion at 3fa81a00, size 12
(devf t2::f3s_ext_write:195) fs0p3 bad H[29] P[1E6] # 00000C # 00000000
(devf t2::f3s_file_create:110) fs0p3 error -1
[t(p) usr/sbin/devf-generic 12290 2 11 80632b4]
[t(c) usr/bin/PSSBSSProcess 213047 1 11 7033519a]
amd_poll: 186 DQ7 polling Timeout
(devf t2::f3s_aCFI_v2write:250) over poll waiting for write completion at 3fa81a0c, size 12
(devf t2::f3s_ext_write:195) fs0p3 bad H[2A] P[1E6] # 00000C # 00000000
(devf t2::f3s_file_create:110) fs0p3 error -1
amd_poll: 186 DQ7 polling Timeout
(devf t2::f3s_aCFI_v2write:250) over poll waiting for write completion at 3fa81a18, size 12
(devf t2::f3s_ext_write:195) fs0p3 bad H[2B] P[1E6] # 00000C # 00000000
(devf t2::f3s_file_create:110) fs0p3 error -1
amd_poll: 186 DQ7 polling Timeout
(devf t2::f3s_aCFI_v2write:250) over poll waiting for write completion at 3fa81a24, size 12
(devf t2::f3s_ext_write:195) fs0p3 bad H[2C] P[1E6] # 00000C # 00000000
(devf t2::f3s_file_create:110) fs0p3 error -1
amd_poll: 186 DQ7 polling Timeout
(devf t2::f3s_aCFI_v2write:250) over poll waiting for write completion at 3fa81a30, size 12
(devf t2::f3s_ext_write:195) fs0p3 bad H[2D] P[1E6] # 00000C # 00000000
(devf t2::f3s_file_create:110) fs0p3 error -1
amd_poll: 186 DQ7 polling Timeout
(devf t2::f3s_aCFI_v2write:250) over poll waiting for write completion at 3fa81a3c, size 12
(devf t2::f3s_ext_write:195) fs0p3 bad H[2E] P[1E6] # 00000C # 00000000
(devf t2::f3s_file_create:110) fs0p3 error -1
[t(p) usr/sbin/devf-generic 12290 2 11 8066bc8]
[t(c) usr/bin/PSSBSSProcess 213047 1 11 7033519a]

--------------------------------
when i try to use the mmi appear blocked but i see a loop of this message and change only the voice "completion at xxxx"

Crash-100

29.02.2016, 17:27

erase efs-persist mmi restore for them self

parsec82

29.02.2016, 17:56

You wish to delete all the content in the /mnt/efs-persist ?

audijiJQ

01.03.2016, 05:04

You wish to delete all the content in the /mnt/efs-persist ?

flashit -a 6200000 -e 1000

parsec82

02.03.2016, 13:06

flashit -a 6200000 -e 1000

ok i have used this line but when i start the unit work for about 10-20 sec and will freeze and on the terminal i see this:

--> SAM is initialized
..initializing addon "SSSMonitor" ...ok
..initializing channel "HostAgent" ...ok
..initializing channel "MonitorService" ...ok
..initializing channel "IntegrityService" ...ok
..initializing channel "AliveService" ...ok
..initializing channel "AudioMatrixService" ...ok
..initializing channel "PhoneService" ...ok
..initializing channel "BSSService" ...ok
[t(p) usr/bin/PSSBSSProcess 213046 3 11 782547b4]
..initializing channel "NetAccessService" ...ok
..initializing channel "SIMService" ...ok
amd_poll: 186 DQ7 polling Timeout
(devf t2::f3s_aCFI_v2write:250) over poll waiting for write completion at 3fb0025c, size 12
(devf t2::f3s_ext_write:195) fs0p3 bad H[06] P[1E8] # 00000C # 00000000
(devf t2::f3s_file_create:110) fs0p3 error -1
amd_poll: 186 DQ7 polling Timeout
(devf t2::f3s_aCFI_v2write:250) over poll waiting for write completion at 3fb00268, size 12
(devf t2::f3s_ext_write:195) fs0p3 bad H[07] P[1E8] # 00000C # 00000000
(devf t2::f3s_file_create:110) fs0p3 error -1
amd_poll: 186 DQ7 polling Timeout
(devf t2::f3s_aCFI_v2write:250) over poll waiting for write completion at 3fb00274, size 12
(devf t2::f3s_ext_write:195) fs0p3 bad H[08] P[1E8] # 00000C # 00000000
(devf t2::f3s_file_create:110) fs0p3 error -1
[t(p) usr/sbin/devf-generic 12290 2 11 8066bc8]
[t(c) usr/bin/PSSBSSProcess 213046 1 11 7033519a]
amd_poll: 186 DQ7 polling Timeout
(devf t2::f3s_aCFI_v2write:250) over poll waiting for write completion at 3fb00280, size 12
(devf t2::f3s_ext_write:195) fs0p3 bad H[09] P[1E8] # 00000C # 00000000
(devf t2::f3s_file_create:110) fs0p3 error -1
amd_poll: 186 DQ7 polling Timeout
(devf t2::f3s_aCFI_v2write:250) over poll waiting for write completion at 3fb0028c, size 12
(devf t2::f3s_ext_write:195) fs0p3 bad H[0A] P[1E8] # 00000C # 00000000
(devf t2::f3s_file_create:110) fs0p3 error -1
amd_poll: 186 DQ7 polling Timeout
(devf t2::f3s_aCFI_v2write:250) over poll waiting for write completion at 3fb00298, size 12
(devf t2::f3s_ext_write:195) fs0p3 bad H[0B] P[1E8] # 00000C # 00000000
(devf t2::f3s_file_create:110) fs0p3 error -1
amd_poll: 186 DQ7 polling Timeout
(devf t2::f3s_aCFI_v2write:250) over poll waiting for write completion at 3fb002a4, size 12
(devf t2::f3s_ext_write:195) fs0p3 bad H[0C] P[1E8] # 00000C # 00000000
(devf t2::f3s_file_create:110) fs0p3 error -1
amd_poll: 186 DQ7 polling Timeout
(devf t2::f3s_aCFI_v2write:250) over poll waiting for write completion at 3fb002b0, size 12
(devf t2::f3s_ext_write:195) fs0p3 bad H[0D] P[1E8] # 00000C # 00000000
(devf t2::f3s_file_create:110) fs0p3 error -1
[t(p) usr/sbin/devf-generic 12290 2 11 8066bc8]
[t(c) usr/bin/PSSBSSProcess 213046 1 11 7033519a]
amd_poll: 186 DQ7 polling Timeout
(devf t2::f3s_aCFI_v2write:250) over poll waiting for write completion at 3fb002bc, size 12
(devf t2::f3s_ext_write:195) fs0p3 bad H[0E] P[1E8] # 00000C # 00000000
(devf t2::f3s_file_create:110) fs0p3 error -1
amd_poll: 186 DQ7 polling Timeout
(devf t2::f3s_aCFI_v2write:250) over poll waiting for write completion at 3fb002c8, size 12
(devf t2::f3s_ext_write:195) fs0p3 bad H[0F] P[1E8] # 00000C # 00000000
(devf t2::f3s_file_create:110) fs0p3 error -1
amd_poll: 186 DQ7 polling Timeout
(devf t2::f3s_aCFI_v2write:250) over poll waiting for write completion at 3fb002d4, size 12
(devf t2::f3s_ext_write:195) fs0p3 bad H[10] P[1E8] # 00000C # 00000000
(devf t2::f3s_file_create:110) fs0p3 error -1
amd_poll: 186 DQ7 polling Timeout
(devf t2::f3s_aCFI_v2write:250) over poll waiting for write completion at 3fb002e0, size 12
(devf t2::f3s_ext_write:195) fs0p3 bad H[11] P[1E8] # 00000C # 00000000
(devf t2::f3s_file_create:110) fs0p3 error -1
amd_poll: 186 DQ7 polling Timeout
(devf t2::f3s_aCFI_v2write:250) over poll waiting for write completion at 3fb002ec, size 12
(devf t2::f3s_ext_write:195) fs0p3 bad H[12] P[1E8] # 00000C # 00000000
(devf t2::f3s_file_create:110) fs0p3 error -1
amd_poll: 186 DQ7 polling Timeout
(devf t2::f3s_aCFI_v2write:250) over poll waiting for write completion at 3fb002f8, size 12
(devf t2::f3s_ext_write:195) fs0p3 bad H[13] P[1E8] # 00000C # 00000000
(devf t2::f3s_file_create:110) fs0p3 error -1
[t(p) usr/sbin/devf-generic 12290 2 11 806334e]
[t(c) usr/bin/PSSBSSProcess 213046 1 11 7033519a]
amd_poll: 186 DQ7 polling Timeout
(devf t2::f3s_aCFI_v2write:250) over poll waiting for write completion at 3fb00304, size 12
(devf t2::f3s_ext_write:195) fs0p3 bad H[14] P[1E8] # 00000C # 00000000
(devf t2::f3s_file_create:110) fs0p3 error -1
amd_poll: 186 DQ7 polling Timeout
(devf t2::f3s_aCFI_v2write:250) over poll waiting for write completion at 3fb00310, size 12
(devf t2::f3s_ext_write:195) fs0p3 bad H[15] P[1E8] # 00000C # 00000000
(devf t2::f3s_file_create:110) fs0p3 error -1
amd_poll: 186 DQ7 polling Timeout