Prolem to connect unit to online

[spinmar]

Hi my friends,
I need your help to solve the problem to connect my unit MMi 3g+ (without sim) to internet (google earth and online services).
Following the advice of Sergey I connected the ami->usb to dlink dub e-100 rev B1 and then dub e-100 to tp link 3040 (with rj45).
I enabled wifi router in my android phone and then I configured the 3040 as wisp client (connected to wifi of my android phone and to dub e100 with rj45).
I see the tplink 3040 as client in my android phone but if I select google earth in navigation nothing happens (in 3040 control panel I don't see any packet from dlink even if I see tx/rx lights in e100).
If I connect my notebook to 3040 with wifi I can navigate and I can navigate also if I connect my notebook to 3040 with rj45.
I see that 3040 gives ip as 192.168.0.X (X>100) while my android phone router in range 192.168.43.X.
The routing tables of 3040 seems ok because with my pc connected with wifi to 3040 I can navigate.
I attach some photos with some screens of hidden menu:

foto1.jpg



foto2.jpg

foto3.jpg

foto4.jpg


foto5.jpg

foto6.jpg


What I'm doing wrong?
Who can help me?
Thanks

[sergeynik]

setup "Install Fair Mode" in eng. menu->config
or run use script next lines

touch /HBpersistence/usedhcp
touch /HBpersistence/DLinkReplacesPPP

[spinmar]

Hi Sergey,
thanks for the help.
I clicked on "Install Fair Mode" in hidden menu: the output was shown in the screen and it seems that it did some backup file and then he created dhcp and dlinkreplacePPP.
Then I rebooted but the result is the same: the google earth remains in onloading and it is no possibile to connect to audi connect.
I attach some screens of hidden menu.
Tplink seems to give the ip 192.168.0.100 to dlink (see image below): if I see this ip is it possibile to think that dhcp of tplink 3040 is working well?
Is this ip correct (for internal routing table) to route packet from MMI to external router android?
Looking at adapter page it seems that dlink is known as 10 full duplex link and not 100 full duplex link: is it correct?
Maybe my ami to usb cable is not so good and I need a more quality cable to support 100 Mbit speed.
(the ami connection is ok because I tried to connect a usb pen and it is ok).
What should be the problem?

foto7.jpg

foto8.jpg

foto9.jpg

foto10.jpg

foto11.jpg

[sergeynik]

speed setup in cfg file in ifs-root

#ASIX Chipset
vendor=0x0b95,device=0x1720,type=ETH,driver=devn-asix.so,args=speed=10 duplex=1,netif=5,netip=172.16.250.248,netmsk=255.2 55.0.0
vendor=0x0b95,device=0x7720,type=ETH,driver=devn-asix.so,args=speed=10 duplex=1,netif=5,netip=172.16.250.248,netmsk=255.2 55.0.0
vendor=0x0846,device=0x1040,type=ETH,driver=devn-asix.so,args=speed=10 duplex=1,netif=5,netip=172.16.250.248,netmsk=255.2 55.0.0
vendor=0x2001,device=0x3c05,type=ETH,driver=devn-asix.so,args=speed=10 duplex=1 phy_88772=0,netif=5,netip=172.16.250.248,netmsk=25 5.255.0.0

[sergeynik]

need up DNS
manual DNS setup. touch in efs-system/etc/resolv.conf
inside file
nameserver 123.123.123.123

[spinmar]

Ho can I install DNS using a script?

[sergeynik]

yes

[spinmar]

Hi Sergey
I tried to write a script to write what you told me.

[sergeynik]

echo nameserver 123.123.123.123 > /mnt/efs-system/etc/resolv.conf

IP DNS set correct !!

[sergeynik]

or create file on PC and copy use script

[spinmar]

Hi Sergey
partial good news.
I installed resolv.conf with a script, following your instruction.
After that Google earth is online, audi connect is ok and also the search using google earth.
Anyway I have no TMC online menu.
If I go to tmc info page in MMI, I don't see any line with "Online traffic data".
In the hidden menu in internal_module_1+2 I have PSD Off selected.
This is my conf:

psd.jpg

Is the error PSD Off?
Do I have to deselect it?
Thanks very much

[spinmar]

I found in the hidden menu a part about TMC which I had as undefined.
I tried to set as online traffic + free tmc but nothing happens: no voice "Online traffic data" in info settings page.
Could you tell me exactly which values to set?
tmc.jpg

[Gsi16]

I found in the hidden menu a part about TMC which I had as undefined.
I tried to set as online traffic + free tmc but nothing happens: no voice "Online traffic data" in info settings page.
Could you tell me exactly which values to set?
tmc.jpg

Spimmar, could you share the script made ​​to the DNS?
thanks ;-)

[spinmar]

Hi Sergey I read that for traffic online is important channel 69 of unit mmi: is it true?
Do you know what value should it be set?
Thanks

[sergeynik]

69 Ch 15Bit (+32768)

[spinmar]

69 Ch 15Bit (+32768)

Sergey you are the men!!!
Thanks very much

[Gsi16]

69 Ch 15Bit (+32768)

Sergey thank you! Are you a big ...!!!
We are implementing a program in linux with rasperry to connect online, if you need the program I share it willingly.

[spinmar]

Sergey one last question.
The question is about my audi pin code: this pin is given after you register a car with native audi connect to my audi site.
This pin let you to transfer poi and travels from pc to MMI.
Sergey, do you know something about it?
In your opinion can we bypass this?

[spinmar]

To activate streeti view it is needed to go down 30 meters in the zoom.

[paszczak]

Hello Sergey, hello all

nice manual - good work

but I have a small problem I have 670G unit so with build in SIM

Spinmar wrote:

To enable online traffic you have select "Online traffic data" to yes and after connecting to audi server, the licence will be activated for 3 years.
After all I attach some screens of what you will have:

but when I am checking license all the time I got answer - currently the query cannot be processed.

any ideas whats wrong?

I had not traffic online factory installed - I added it by channel 69 where I set value 32783. then I got in menu traffic online but impossible to add licence

even I asked about audi - their answer was as usually - this feature existiing from W45 2012 and impossible to add later

pls help me - I am fighting with this since begining of 2013




my current version SW is 770 but same issue I had with 612, 614 and with 518_7

I have screnshots from green menu and others but I am not able to upload anything to this forum

if I will swap 5F to another one it will works? if yes whats a problem that mine doesnt works?