Буду плодить тему.Где вопрос-ответ ответа нет.Нужен график зависимости сопротивления датчика ТОЖ (G62) от температуры.Вроде где-то на форуме есть, но поиск не дал результата.Если у кого есть скиньте или дайте ссыль пожалуйста
Вид для печати
Буду плодить тему.Где вопрос-ответ ответа нет.Нужен график зависимости сопротивления датчика ТОЖ (G62) от температуры.Вроде где-то на форуме есть, но поиск не дал результата.Если у кого есть скиньте или дайте ссыль пожалуйста
а зачем тебе столь сложная информация?
Мегасквирт 3
да, точно было но чот тоже не нашол. вот чо эльза говорит
Checking ignition system
Checking coolant temperature sender -G62
http://turbo-quattro.com/ElsaWin\gra...i/G24-0017.png Special tools and workshop equipment required
- ◆ V.A.G 1526 A
- ◆ V.A.G 1594 A
- ◆ V.A.G 1598 A with V.A.G 1598/5
- ◆ VAS 5051 with VAS 5051/1 and VAS 5051/2
Fitting location => Fitting locations overview, Page 24-5
Test requirements:
- ● Engine cold
http://turbo-quattro.com/ElsaWin\gra...i/A01-0187.png Test sequence
- ‒ Read measured value block, display group 001, engine idling => Page 01-69.
→ Display on VAS 5051:
- ‒ Check display in display zone -2-.
- ‒ Specification: The temperature reading should increase at a uniform rate.
- ‒ Switch ignition off.
http://turbo-quattro.com/ElsaWin\gra...i/V28-0947.png If display zone 2 shows an implausible value:
Check internal resistance
- ‒ Unplug connector on coolant temperature sender.
- ‒ → Connect multimeter between contacts 1 and 2 on sender to measure resistance.
If specification is not attained:
Coolant temperature Resistance approx. 20 °C 1.5...3.0 kω
- ‒ Replace coolant temperature sender.
http://turbo-quattro.com/ElsaWin\gra...i/V96-0749.png If specification is attained:
Check wiring
- ‒ With the ignition switched off, use adapter V.A.G 1598/5 to connect test box V.A.G 1598 A to the connector of the engine control unit and also to the control unit => Page 24-15.
- ‒ → Check for open circuit and short to positive or earth in the following wiring connections:
Connector
ContactTest box V.A.G 1598 A
Socket1 45 2 30
- ‒ Test for short circuits between the two wires.
- ‒ Use current flow diagram to eliminate open circuit in wiring/short circuit.
If no wiring fault is detected:
- ‒ Replace engine control unit => Page 24-18.
Что то близко к этому вроде
http://clip2net.com/clip/m51276/thum...-clip-34kb.jpg
Ок спасибо
Жаль минусовой температуры нет
этот график эльза для adcшного датчика выдает
Еп-топ-топ наверное надо будет в морзиловку с тестером сувать
он же от 2,6/2,8, не думаю, что там принципально что-то другое